Rice Lake 720i Programmable Indicator/Controller - Installation Manual - Manual (Page 94)

88 720i Installation Manual
SC.DFTHRH#1 Digital filter cutout threshold NONE, 2D, 5D, 10D, 20D, 50D, 100D, 200D, 250D
SC.RATLTRAP#1 Rattletrap filtering OFF, ON
SC.SMPRAT#1 Sample rate 7.5HZ, 15HZ, 30HZ, 60HZ, 120HZ, 240HZ, 480HZ, 960HZ
SC.PWRUPMD#1 Power up mode GO, DELAY
SC.TAREFN#1 Tare function BOTH, NOTARE, PBTARE, KEYED
SC.PRI.DECPNT#1 Primary units decimal position 8.888888, 88.88888, 888.8888, 8888.888, 88888.88,
888888.8, 8888888, 8888880, 8888800
SC.PRI.DSPDIV#1 Primary units display divisions 1D, 2D, 5D
SC.PRI.UNITS#1 Primary units LB, KG, G, OZ, TN, T, GR, troyoz, troylb, LT, CUSTOM, NONE,
OFF
SC.PRI.CUNITS#1 Primary custom units Specify units if SC.PRI.UNITS=CUSTOM
SC.SEC.DECPNT#1 Secondary units decimal position 8.888888, 88.88888, 888.8888, 8888.888, 88888.88,
888888.8, 8888888, 8888880, 8888800
SC.SEC.DSPDIV#1 Secondary units display divisions 1D, 2D, 5D
SC.SEC.UNITS#1 Secondary units LB, KG, G, OZ, TN, T, GR, troyoz, troylb, LT, CUSTOM, NONE,
OFF
SC.SEC.CUNITS#1 Secondary custom units Specify units if SC.SEC.UNITS=CUSTOM
SC.SEC.MULT#1 Secondary units multiplier 0.00000–9999999
SC.TER.UNITS#1 Tertiary units LB, KG, G, OZ, TN, T, GR, troyoz, troylb, LT, CUSTOM, NONE,
OFF
SC.TER.CUNITS#1 Tertiary custom units Specify units if SC.TER.UNITS=CUSTOM
SC.TER.DECPNT#1 Tertiary units decimal position 8.888888, 88.88888, 888.8888, 8888.888, 88888.88,
888888.8, 8888888, 8888880, 8888800
SC.TER.DSPDIV#1 Tertiary units display divisions 1D, 2D, 5D
SC.TER.MULT#1 Tertiary units multiplier 0.000001–9999999
SC.ROC.DECPNT#1 Tertiary units decimal position 8.888888, 88.88888, 888.8888, 8888.888, 88888.88,
888888.8, 8888888, 8888880, 8888800
SC.ROC.DSPDIV#1 Rate-of-change units display divisions 1D, 2D, 5D
SC.ROC.MULT#1 Rate-of-change units multiplier 0.000001–9999999
SC.ROC.UNITS#1 Rate-of-change units SEC, MIN, HOUR
SC.ROC.INTERVL#1 Rate-of-change interval 1–100
SC.ROC.REFRESH#1 Rate-of-change refresh interval 0.1–60
SC.RANGE1.MAX#1 Weight maximum for first range or
interval weight
SC.RANGE2.MAX#1 Weight maximum for second range or
interval weight
SC.RANGE3.MAX#1#1 Weight maximum for third range or
interval weight
SC.ACCUM#1 Accumulator enable ON, OFF
SC.VISIBLE#1 Scale visibility ON, OFF
SC.PEAKHOLD#1 Peak hold OFF, NORMAL, BI-DIR, AUTO
SC.WZERO#1 Zero calibration —
SC.WVAL#1 Test weight value test_weight_value
SC.WSPAN#1 Span calibration —
SC.WLIN.F1#1–
SC.WLIN.F5#1 Actual raw count value for linearization
points 1–5 0–16777215
Command Description Values
Table 10-3. SCALES Serial Commands (Continued)