Rice Lake 720i Programmable Indicator/Controller - Installation Manual - Manual (Page 10)

4 720i Installation Manual
Right and Left navigation keys to select the
digit.
3. Press the Print softkey or the front panel PRINT
key to print using the selected auxiliary format.
Accumulator Functions
The accumulator must be enabled before use. Once
enabled, weight (net weight if a tare is in the system) is
accumulated whenever a print operation is performed
using the
PRINT key, digital input, or serial command.
The scale must return to zero (net zero if a tare is in the
system) before the next accumulation.
The Display Accum softkey can be configured to display
the current accumulator value. Printing while the
accumulator is displayed uses the ACCFMT print
format (see Section 6.0 on page 52).
Press the CLEAR key twice to clear the accumulator.
Note
With the panel mount version of the 720i, you
need to use CLR Accumulator DigIn Function
to clear the indicator.
1.3 Softkey Operations
Softkeys provide additional operator functions for
specific applications. Softkey assignments are listed on
the tabs shown at the bottom of the LCD display;
softkey functions are activated by pressing the arrow
keys below the softkey tabs (see Figures 1-1 and 1-2 on
page 2).
For example, to set up a TimeDate softkey using serial
commands, do the following:
1. Place indicator in setup mode.
2. Send the following serial command:
SK#s=TimeDate
where s is the softkey position.
3. Press SaveExit (or send the KSAVEEXIT serial
command). The new softkey will appear in the
position specified by s.
4. Press the TimeDate softkey. Use the Up/Down
navigation keys to adjust the time and date
value; use the
Left/Right keys to move between
fields. Time and date fields are presented in the
following order:
HOUR>MIN>[AM/PM]>MONTH>DAY>YEAR
When done, press Enter to return to weighing
mode.
The particular set of softkeys shown on the display can
be set using serial commands or
Revolution III .
Table 1-1. Configurable Softkeys
Softkey Description
None Not Configured, no softkeys will appear
after a none key.
Empty Key, allows for a space/blank
between other softkeys.
Time/Date Displays current time and date; allows
time and date change.
Display Tare Displays tare value for the current scale
Display Accum Displays accumulator value, if enabled, for
the current scale.
Display ROC Displays rate-of-change value, if enabled,
for the current scale.
***Weigh In Allows truck ID entry; generates weigh-in
ticket for truck weighing applications.
***Weigh Out Allows truck ID entry; generates weigh-out
ticket for truck weighing applications.
***Truck Regs Displays truck register; allows deletion of
individual or all entries. Truck register can
be printed by pressing the PRINT key
while the truck register is displayed.
Alibi Allows previous print transactions to be
recalled and reprinted.
SKUD 1-10 User-programmable keys; defined by
PCEE .
**Setpoint Displays a menu of configured setpoints;
allows display and change of some
setpoint parameters.
**Batch Start Starts a configured batch.
**Batch Stop Stops a running batch and turns off all
associated digital outputs. Requires a
batch start to resume processing.
**Batch Pause Pauses a running batch. (Same as stop,
but digital outputs, if on, are not turned
off.)
**Batch Reset Stops a batch and resets it to the first
batch step.
*Weigh Start the Weigh-In and Weigh-Out
Procedure.
*Reports Select which report to print. There are four
sub menus under the Reports softkey:
Summary, Daily, Detail, and Code List.
*Management Add and remove materials, customers,
and source IDs and names.
More… For applications with more than three
defined softkeys, the More… key is
automatically assigned to the fourth
softkey position. Press More… to toggle
between groups of softkeys.
* Advance Truck Mode only
** 720i Batching Version software only
*** Truck Modes 1-6 only