Dell 2135cn Color Laser Printer - Manual (Page 229)

Values:
Fax Settings
Purpose:
To confirm the Fax settings.
Values:
NOTE: Values marked by an asterisk (*) are the factory default menu settings.
Resolution
Standard* Suitable for documents with normal sized characters.
Fine Suitable for documents containing small characters or thin lines or documents printed using a dot-matrix printer.
Super Fine
Suitable for documents containing extremely fine detail. The super fine mode is enabled only if the remote machine also
supports the Super Fine resolution.
Photo Suitable for documents containing photographic images.
Lighter/Darker Sets the default density to fax your documents lighter or darker.
Delayed Start Sets the fax transmission start time when sending a fax at a specified time.
NOTE: Values marked by an asterisk (*) are the factory default menu settings.
Receive Mode
Fax* Automatically receives faxes.
Telephone
Automatic fax reception is turned off. You can receive a fax by picking up the handset of the external phone and then
pressing a remote receive code, or by setting OnHook to On (you can hear voice or fax tones from the remote machine)
and then pressing .
Telephone/Fax
When the printer receives an incoming fax, the external telephone rings for the time specified in Auto Receive
Fax/Tel, and then the printer automatically receives a fax. If an incoming call is not a fax, the printer beeps from the
internal speaker indicating that the call is a telephone call.
Answer
Machine/Fax
The printer can share a telephone line with an answering machine. In this mode, the printer will monitor the fax signal
and pick up the line if there are fax tones. If the phone communication in your country is serial, this mode is not
supported.
DRPD
Before using the Distinctive Ring Pattern Detection (DRPD) option, a distinctive ring service must be installed on your
telephone line by the telephone company. After the telephone company has provided a separate number for faxing
with a distinctive ring pattern, configure the fax setup to monitor for that specific ring pattern.
Auto Receive
Fax
Sets the interval at which the printer goes into the fax receive mode after answering an incoming call.
Auto Receive
Fax/Tel
Sets the interval at which the printer goes into the fax receive mode after the external telephone receives an incoming call.
Auto Receive
Answer/Fax
Sets the interval at which the printer goes into the fax receive mode after the external answering machine receives an incoming call.
Line Monitor Sets the volume of the line monitor, which audibly monitors a transmission through the internal speaker until a connection is made.
Ring Tone
Volume Sets the volume of the ring tone, which indicates that an incoming call is a telephone call through the internal speaker when Receive
Mode is set to Telephone/Fax.
Line Type Sets the default line type; PSTN or PBX.
Tone/Pulse Sets whether to use tone or pulse dialing.
Resend Delay Sets the interval (3-255 seconds) between resend attempts.
Redial Attempts Sets the number of redial attempts (0-13) to make if the destination fax number is busy. If you enter 0, the printer will not redial.
Redial Delay Sets the interval (1-15 minutes) between redial attempts.
Junk Fax Setup Sets whether or not to reject unwanted faxes by accepting only the faxes from the numbers registered in the Phone Book
Remote Receive Sets whether or not to receive a fax by pressing a remote receive code on the external telephone.
Remote Receive
Tone
Specifies a 2-digit remote receive code when Remote Receive is On.
Fax Header Sets whether to print the sender's information on the header of faxes.
Fax Header
Name
Allows you to enter a name that will be printed on the header of faxes.
Fax Number Allows you to enter the fax number of the printer, which will be printed on the header of faxes.
Fax Cover Page Sets whether or not to attach a cover page to faxes.
DRPD Pattern
Sets the Distinctive Ring Pattern Detection (DRPD) setting from Pattern1 to Pattern7. DRPD is a service provided by some telephone
companies.
Sent Fax
Forward
Sets whether to forward incoming faxes to a specified destination.
Fax Forward
Number
Allows you to enter the fax number of the destination to which incoming faxes will be forwarded.
Fax Forward
Print
Sets whether to print all forwarded faxes.
Fax Forward
Error Print
Sets whether to print only faxes that failed to be forwarded when Fax Forward Print is Off.