Dell 2135cn Color Laser Printer User Manual

Page 112

Ring Tone
Volume

Sets the volume of the ring tone, which indicates that an incoming call is a telephone call through the internal speaker when Receive Mode is
set to Telephone/Fax.

Line Type

You can select the default line type.

PSTN

PBX

Tone/Pulse

You can select the dialing type.

Tone

Pulse (10PPS)

Pulse (20PPS)

Resend
Delay

You can specify the interval between transmission attempts within the range of 3 to 255 seconds. The default is 8 seconds.

Redial
Attempts

You can specify the number of redial attempts to make when the destination fax number is busy, within the range of 0 to 13. If you enter 0,
the printer will not redial.

Redial Delay Your printer can automatically redial a remote fax machine if it was busy. Intervals from 1-15 minutes can be entered.

Junk Fax
Setup

You can reject faxes sent from unwanted stations. The system only accepts faxes from the remote stations registered in the speed dial. This
feature is useful for blocking any unwanted faxes.

Select Off to turn the feature off. Anybody can send you a fax.

Select On to turn the feature on.

Remote
Receive

You can receive a fax by pressing the remote receive code on the external telephone after picking up the handset of the telephone.

Remote Rcv
Tone

You can specify the tone when Remote Receive is set to On.

Fax Header

Prints the sender's information on the header of faxes.

Select Off to turn this feature off.

Select On to turn this feature on.

Fax Header
Name

Specifies the sender's name to be printed on the header of faxes.

Fax Number

Specifies the fax number of the printer, which will be printed on the header of faxes. This feature is available when you set Fax Header to On.
The number specified in Fax Number is used in the printer ID.

Fax Cover
Page

You can set whether to attach a cover page to faxes when sending faxes.

DRPD
Pattern

Before using the Distinctive Ring Pattern Detection (DRPD) option, distinctive ring service must be installed on your telephone line by the
telephone company. After the telephone company has provided a separate number for faxing with a distinctive ring pattern, configure the fax
setup to monitor for that specific ring pattern.

Sent Fax
Fwd

You can set your printer to forward incoming faxes to another fax number. When a fax arrives at your printer, it is stored in the memory.
Then, the printer dials the fax number that you have specified and sends the fax.

Select Only On Error to forward incoming faxes when an error occurs.

Select On to always forward incoming faxes.

Select Off not to forward incoming faxes.

Fax Fwd
Number

You enter the fax number of the destination to which incoming faxes will be forwarded.

Fax Fwd
Print

You can set whether to print all forwarded incoming faxes.

Fax Fwd Err
Print

Prints incoming faxes that failed to be forwarded when Fax Fwd Print is set to Off.

Prefix Dial

You can specify whether or not to set a prefix dial number.

Prefix Dial
Num

You can set a prefix dial number of up to five digits. This number dials before any auto dial number is started. It is useful for accessing the
Private Automatic Branch Exchange (PABX).

Discard Size

When receiving a document as long as or longer than the paper installed in your printer, you can set the printer to discard any excess at the
bottom of the page. If the received page is outside the margin you set, it will print on two sheets of paper at the actual size. When the
document is within the margin and Discard Size is set to Auto Reduction, the printer reduces the document to fit it onto the appropriate
sized paper and discard does not occur. If Discard Size is set to other than Auto Reduction, the data within the margin will be discarded.

ECM

You can set whether to enable or disable the ECM (Error Correction Mode).

Modem
Speed

You can set the modem speed.

Country

You can select the country where the printer is used.

Fax Activity

You can set whether to automatically print a fax activity report after every 50 incoming and outgoing fax communications.

Fax
Transmit

You can set whether to print a transmission result after a fax transmission.

Fax
Broadcast

You can set whether to print a transmission result after a fax transmission to multiple locations.

Fax Protocol You can set whether to print the protocol monitor report after a fax transmission to monitor fax protocol problems.