Franklin Fueling Systems TS 550 evo Fuel Management System Operators Guide - Manual (Page 34)

30
Displayed Alarm /
Warning
Device Description Recommended Actions
High water level Tank Water level exceeded High limit
set.
Verify programmed level. If water is too high consult you local site
policy procedures for corrective actions.
High Water/Phase Sep Tank Water/Phase Separation has
exceeded the High Limit set.
Remove Water/Phase Separated product form the tank.
Level error Tank Product level exceeds tank
diameter due to an error in
console of programming.
Verify tank, offset, and probe programming.
Line monitor disabled Line Specified line is not enabled, so
line leak test will not be performed.
Verify line programming. If necessary enable line.
Low battery Tank Backup battery is low. See Installation Guide for replacement instructions.
Low product volume Tank/
Manifold
Product volume below Low limit
set. The tank / manifold specified
may be near empty.
Acquire an accurate product volume. If actual product volume in
tank does not match the consoles displayed current volume, verify
programming.
Low low product volume Tank/
Manifold
Product volume below Low
Low limit. The tank or manifold
specified may be near empty.
Acquire an accurate product volume, and if does not match the
consoles displayed current volume, verify programming.
Mag installation error Sensor The specified TSP-DMS has an
installation error
Check the installation of the TSP-DMS, the sensor must be plumb.
If installation is correct, then try to relearn the sensor. If the problem
persist, the sensor may need to be replaced
Mag product alarm Sensor The specified TSP-DMS has
detected product.
Inspect the sump for the presence of product.
Mag sensor configuration
error
Sensor An error has been detected in the
configuration of the specified TSP-
DMS.
Enter into the setup and inspect the TSP-DMS setup.
Mag sensor data error Sensor There is an error with the reported
data from the specified TSP-DMS
Inspect wire connections at the Mag sensor. If the problem persists,
contact FFS Technical Services for support.
Mag sensor float height
error
Sensor The float height has exceeded the
limits as learned.
Inspect wire connections at the Mag sensor. If the problem persists,
contact FFS Technical Services for support.
Mag sensor float missing Sensor The specified TSP-DMS is not
reporting the level information for
one or more float.
Inspect the Mag sensor for damage and redo the connections. If the
Problem persists, contact FFS Technical Services.
Mag sensor missing Sensor The console is not receiving any
information from the specified
TSP-DMS.
Inspect wire connections at the Mag sensor. If the problem persists,
contact FFS Technical Services.
Mag sensor not learned
error
Sensor The specified TSP-DMS was not
properly learned.
Enter into the Control > Mag Sensor screen and have the console
learn the sensor.
Mag sensor
synchronization error
Sensor The console is receiving
incomplete or improperly timed
data from the specified
TSP-DMS
Inspect wire connections at the Mag sensor. If the problem persists,
contact FFS Technical Services.
Mag water alarm Sensor The specified TSP-DMS has
detected water.
Inspect the sump for water.
Mag water warning Sensor The TSP-DMS has detected water
above the preset limit.
Inspect the sump for water.
Manifold Delivery
Detected
Tank A delivery has been detected on
the specified manifold.
This is not an alarm and should only be a concern if there was not a
delivery to the site at the specified date and time.
Manifold Gross Leak
Detected
Tank A leak in the specified manifolded
tanks has been detected via a
SCALD test. Suspect possible
leak.
Review Tank Leak Test History and programming.
Refer to Section 5: Misc / Tank Leak Tests – Type and Frequency for
instructions on manually starting line leak tests.
Manifold Leak Detected Tank A leak in the specified manifolded
tanks has been detected via a
SCALD test. Suspect possible leak
Review Tank Leak Test History and programming.
Refer to Section 5: Misc/Tank Leak Tests – Type and Frequency for
instructions on manually starting line leak tests.
Manifold low product
volume
Tank The specified manifold has
reached the programmed Low
Product Volume
Check product volume and compare to the programmed Low Volume
alarm Limit in the setup menu. Acquire an accurate product volume
and compare to the ATG. If levels differ, verify programming is correct.
If alarm persists, contact FFS Technical Services for support.
Manifold low low product
volume
Tank The specified manifold has
reached the programmed Low
Low Product Volume
Check product volume and compare to the programmed Low Low
Volume alarm Limit in the setup menu. Acquire an accurate product
volume and compare to the ATG. If levels differ, verify programming is
correct. If alarm persists, contact FFS Technical Services for support.
Manifold Leak Detected Tank A leak in the specified manifolded
tanks has been detected via a
SCALD test. Suspect possible
leak.
Review Tank Leak Test History and programming. Refer to Section
5: Misc/Tank Leak Tests – Type and Frequency for instructions on
manually starting line leak tests.