Renesas RJJ10J1643-0101 - Manual (Page 187)

Rev.1.01 2007.02.16
RJJ10J1643-0101 185
(Resolution) Specify one from { RAPI_10BIT, RAPI_8BIT }. The default value is
RAPI_8BIT.
(Operating
states set)
Specify one from { RAPI_AD_ON, RAPI_AD_OFF }. The default value is
RAPI_AD_OFF.
(Conversion
method)
Specify one from { RAPI_WITH_SAMPLE_HOLD,
RAPI_WITHOUT_SAMPLE_HOLD }. The default value is
RAPI_WITHOUT_SAMPLE_HOLD.
(Trigger) Specify one from { RAPI_SOFTWARE_TRIGGER,
RAPI_EXTERNAL_TRIGGER }. The default value is
RAPI_SOFTWARE_TRIGGER.
• Specifiable definition values when repeat sweep mode 1 is used
(RAPI_REPEAT_SWEEP1 specified)
(Input pin) Specify one from { RAPI_P0_GROUP, RAPI_P10_GROUP,
RAPI_P1P9_GROUP, RAPI_P9_GROUP }. The default value is
RAPI_P10_GROUP.
(Operating
frequency)
Specify one from { RAPI_FAD, RAPI_FAD2, RAPI_FAD3, RAPI_FAD4,
RAPI_FAD6, RAPI_FAD12 }. The default value is RAPI_FAD4.
(Resolution) Specify one from { RAPI_10BIT, RAPI_8BIT }. The default value is
RAPI_8BIT.
(Operating
states set)
Specify one from { RAPI_AD_ON, RAPI_AD_OFF }. The default value is
RAPI_AD_OFF.
(Conversion
method)
Specify one from { RAPI_WITH_SAMPLE_HOLD,
RAPI_WITHOUT_SAMPLE_HOLD }.
The default value is RAPI_WITHOUT_SAMPLE_HOLD.
(Trigger) Specify one from { RAPI_SOFTWARE_TRIGGER,
RAPI_EXTERNAL_TRIGGER }.
The default value is RAPI_SOFTWARE_TRIGGER.
• Specifiable definition values when simultaneous sampling sweep mode is used
(RAPI_SIMULTANEOUS_SAMPLE_SWEEP specified)
(Input pin) Specify one from { RAPI_P0_GROUP, RAPI_P10_GROUP,
RAPI_P1P9_GROUP, RAPI_P9_GROUP }. The default value is
RAPI_P10_GROUP.
(Operating
frequency)
Specify one from { RAPI_FAD, RAPI_FAD2, RAPI_FAD3, RAPI_FAD4,
RAPI_FAD6, RAPI_FAD12 }. The default value is RAPI_FAD4.
(Resolution) Specify one from { RAPI_10BIT, RAPI_8BIT }. The default value is
RAPI_8BIT.
(Operating
states set)
Specify one from { RAPI_AD_ON, RAPI_AD_OFF }. The default value is
RAPI_AD_OFF.
(Trigger) Specify one from { RAPI_SOFTWARE_TRIGGER, RAPI_EXTERNAL_TRIGGER,
RAPI_TIMER_B0_TRIGGER, RAPI_TIMER_B2_TRIGGER,
RAPI_ICTB2_TRIGGER }. The default value is RAPI_SOFTWARE_TRIGGER.
• Specifiable definition values when delayed trigger mode 0 is used
(RAPI_DELAYED_TRIGGER0 specified)
(Input pin) Specify one from { RAPI_P0_GROUP, RAPI_P10_GROUP,
RAPI_P1P9_GROUP, RAPI_P9_GROUP }. The default value is
RAPI_P10_GROUP.
(Operating
frequency)
Specify one from { RAPI_FAD, RAPI_FAD2, RAPI_FAD3, RAPI_FAD4,
RAPI_FAD6, RAPI_FAD12 }. The default value is RAPI_FAD4.