Renesas RJJ10J1643-0101 - Manual (Page 175)

Rev.1.01 2007.02.16
RJJ10J1643-0101 173
RAPI_INT2 Uses _INT2 interrupt.
RAPI_INT3 Uses _INT3 interrupt.
RAPI_KEY Uses key input interrupt.
RAPI_INT_RISING Specifies a rising edge for the active edge of a selected external
interrupt.
RAPI_INT_FALLING Specifies a falling edge for the active edge of a selected external
interrupt.
RAPI_INT_BOTH Specifies both edges for the active edge of a selected external
interrupt.
RAPI_FILTER_F1 Uses the digital filter facility that has a sampling frequency f
1
.
RAPI_FILTER_F8 Uses the digital filter facility that has a sampling frequency f
8
.
RAPI_FILTER_F32 Uses the digital filter facility that has a sampling frequency f
32
.
RAPI_KI0_FALLING Enables _KI0 pin input whose falling edge is the active edge.
RAPI_KI0_RISING Enables _KI0 pin input whose rising edge is the active edge.
RAPI_KI1_FALLING Enables _KI1 pin input whose falling edge is the active edge.
RAPI_KI1_RISING Enables _KI1 pin input whose rising edge is the active edge.
RAPI_KI2_FALLING Enables _KI2 pin input whose falling edge is the active edge.
RAPI_KI2_RISING Enables _KI2 pin input whose rising edge is the active edge.
RAPI_KI3_FALLING Enables _KI3 pin input whose falling edge is the active edge.
RAPI_KI3_RISING Enables _KI3 pin input whose rising edge is the active edge.
• Specifiable definition values when _INT0 to _INT3 interrupt is used (RAPI_INT0 to
RAPI_INT3 specified)
(Polarity) Specify one from { RAPI_INT_RISING, RAPI_INT_FALLING,
RAPI_INT_BOTH }. The default value is RAPI_INT_FALLING.
(Filter) Specify one from { RAPI_FILTER_F1, RAPI_FILTER_F8,
RAPI_FILTER_F32 }. If no filters are specified, “No filter” is set.
• Specifiable definition values when key input interrupt is used (RAPI_KEY specified)
(_KI0 pin input) Specify one from { RAPI_KI0_FALLING, RAPI_KI0_RISING }. If _KI0 pin
input is not specified, “_KI0 pin input disabled” is set.
(_KI1 pin input) Specify one from { RAPI_KI1_FALLING, RAPI_KI1_RISING }. If _KI1 pin
input is not specified, “_KI1 pin input disabled” is set.
(_KI2 pin input) Specify one from { RAPI_KI2_FALLING, RAPI_KI2_RISING }. If _KI2 pin
input is not specified, “_KI2 pin input disabled” is set.
(_KI3 pin input) Specify one from { RAPI_KI3_FALLING, RAPI_KI3_RISING }. If _KI3 pin
input is not specified, “_KI3 pin input disabled” is set.
(H8/300H)
RAPI_IRQ0 Uses IRQ0 interrupt.
RAPI_IRQ1 Uses IRQ1 interrupt.
RAPI_IRQ2 Uses IRQ2 interrupt.
RAPI_IRQ3 Uses IRQ3 interrupt.
RAPI_WKP Uses WKP interrupt.
RAPI_NOT_INT_
REQUEST
Does not request assertion of interrupt for a selected external
interrupt.
RAPI_INT_REQUEST Requests assertion of interrupt for a selected external interrupt.