Kohler Command Pro CV980 - Manual (Page 72)

7.22
Section 7
Electrical System and Components
řǯȱ —œŠ••ȱ‘Žȱ˜ěœŽȱ‘›žœȱǻœ˜™Ǽȱ Šœ‘Ž›ȱœ˜ȱ‘Žȱ
œ–Š••Ž›ȱȃ˜ěœŽȄȱ˜ȱ‘Žȱ Šœ‘Ž›ȱŠŒŽœȱ‘Žȱ›ŽŠ’—Ž›Ȧ
Œ˜••Š›ǯȱŽŽȱ’ž›ŽȱŝȬřşǯ
Figure 7-39. Installing Thrust Washer.
ȱ Śǯȱ ™™•¢ȱŠȱœ–Š••ȱŠ–˜ž—ȱ˜ȱ˜’•ȱ˜ȱ‘Žȱ‹ŽŠ›’—ȱ’—ȱ‘Žȱ
drive end cap, and install the armature with the
drive pinion.
ȱ śǯȱ ž‹›’ŒŠŽȱ‘Žȱ˜›”ȱŽ—ȱŠ—ȱŒŽ—Ž›ȱ™’Ÿ˜ȱ˜ȱ‘Žȱ
›’ŸŽȱ•ŽŸŽ›ȱ ’‘ȱ›’ŸŽȱ•ž‹›’ŒŠ—ȱǻœŽŽȱŽŒ’˜—ȱŘǼǯȱ
˜œ’’˜—ȱ‘Žȱ˜›”ȱŽ—ȱ’—˜ȱ‘Žȱœ™ŠŒŽȱ‹Ž ŽŽ—ȱ‘Žȱ
captured washer and the rear of the pinion.
ȱ Ŝǯȱ •’Žȱ‘ŽȱŠ›–Šž›Žȱ’—˜ȱ‘Žȱ›’ŸŽȱŽ—ȱŒŠ™ǰȱŠ—ȱ
at the same time seat the drive lever into the
housing.
DZȱ ˜››ŽŒ•¢ȱ’—œŠ••Žǰȱ‘ŽȱŒŽ—Ž›ȱ™’Ÿ˜ȱ
œŽŒ’˜—ȱ˜ȱ‘Žȱ›’ŸŽȱ•ŽŸŽ›ȱ ’••ȱ‹Žȱ̞œ‘ȱ
˜›ȱ‹Ž•˜ ȱ‘Žȱ–ŠŒ‘’—Žȱœž›ŠŒŽȱ˜ȱ‘Žȱ
‘˜žœ’—ȱ ‘’Œ‘ȱ›ŽŒŽ’ŸŽœȱ‘Žȱ‹ŠŒ”ž™ȱ
Šœ‘Ž›ǯȱŽŽȱ’ž›ŽȱŝȬŚŖǯ
Figure 7-40. Installing Armature and Pivot Lever.
ȱ ŝǯȱ —œŠ••ȱ‘Žȱ‹ŠŒ”ž™ȱ Šœ‘Ž›ǰȱ˜••˜ Žȱ‹¢ȱ‘Žȱ›ž‹‹Ž›ȱ
grommet, into the matching recess of the drive
end cap. The molded recesses in the grommet
œ‘˜ž•ȱ‹Žȱȃ˜žȄǰȱ–ŠŒ‘’—ȱŠ—ȱŠ•’—Žȱ ’‘ȱ
‘˜œŽȱ’—ȱ‘ŽȱŽ—ȱŒŠ™ǯȱŽŽȱ’ž›ŽȱŝȬŚŗǯ
Figure 7-41. Installing Backup Washer and
Grommet.
ȱ Şǯȱ —œŠ••ȱ‘Žȱ›Š–Žǰȱ ’‘ȱ‘Žȱœ–Š••ȱ—˜Œ‘ȱ˜› Š›ǰȱ
˜—˜ȱ‘ŽȱŠ›–Šž›ŽȱŠ—ȱ›’ŸŽȱŽ—ȱŒŠ™ǯȱ•’—ȱ‘Žȱ
notch with the corresponding section in the
›ž‹‹Ž›ȱ›˜––Žǯȱ—œŠ••ȱ‘Žȱ›Š’—ȱž‹Žȱ’—ȱ‘Žȱ›ŽŠ›ȱ
Œž˜žǰȱ’ȱ’ȱ Šœȱ›Ž–˜ŸŽȱ™›ŽŸ’˜žœ•¢ǯȱŽŽȱ’ž›Žȱ
ŝȬŚŘǯ
Figure 7-42. Installing Frame and Drain Tube.
ȱ şǯȱ —œŠ••ȱ‘Žȱ̊ȱ‘›žœȱ Šœ‘Ž›ȱ˜—˜ȱ‘ŽȱŒ˜––žŠ˜›ȱ
Ž—ȱ˜ȱ‘ŽȱŠ›–Šž›Žȱœ‘ŠĞǯȱŽŽȱ’ž›ŽȱŝȬŚřǯ
Thrust Washer