Kohler Command Pro CV980 - Manual (Page 40)

5.12
Section 5
Fuel System and Governor
Figure 5-26. Installing Float Assembly.
ŗŚǯȱ ˜•ȱ‘ŽȱŒŠ›‹ž›Ž˜›ȱ‹˜¢ȱœ˜ȱ‘Žȱ̘ŠȱŠœœŽ–‹•¢ȱ
hangs vertically and rests lightly against the
fuel inlet needle. The inlet needle should be
fully seated but the center pin of the needle (on
retainer clip end) should not be depressed. Check
‘Žȱ̘Šȱ‘Ž’‘ȱŠ“žœ–Ž—ǯ
DZȱ ‘Žȱ’—•Žȱ—ŽŽ•ŽȱŒŽ—Ž›ȱ™’—ȱ’œȱœ™›’—ȱ
•˜ŠŽǯȱŠ”Žȱœž›Žȱ‘Žȱ̘Šȱ›ŽœœȱŠŠ’—œȱ
the fuel inlet needle without depressing
the center pin.
ŗśǯȱ ‘ŽȱŒ˜››ŽŒȱ̘Šȱ‘Ž’‘ȱœŽĴ’—ȱ’œȱ17 mm (0.669
in.) ± 1.5 mm (0.059 in.)ǰȱ–ŽŠœž›Žȱ›˜–ȱ‘Žȱ̘Šȱ
‹˜Ĵ˜–ȱ˜ȱ‘Žȱ‹˜¢ȱ˜ȱ‘ŽȱŒŠ›‹ž›Ž˜›ǯȱŽŽȱ’ž›Žȱ
śȬŘŝǯȱŽ™•ŠŒŽȱ‘Žȱ̘Šȱ’ȱ‘Žȱ‘Ž’‘ȱ’œȱ’쎛Ž—ȱ
‘Š—ȱœ™ŽŒ’ꮍǯȱ˜ȱ—˜ȱŠĴŽ–™ȱ˜ȱŠ“žœȱ‹¢ȱ
‹Ž—’—ȱ‘Žȱ̘ŠȱŠ‹ǯ
DZȱ Žȱœž›Žȱ˜ȱ–ŽŠœž›Žȱ›˜–ȱ‘ŽȱŒŠœ’—ȱ
surface, not the rubber gasket, if still
ŠĴŠŒ‘Žǯ
Figure 5-27. Checking Float Height.
ŗŜǯȱ ‘Ž—ȱ‘Žȱ™›˜™Ž›ȱ̘Šȱ‘Ž’‘ȱ’œȱ˜‹Š’—Žǰȱ
carefully reinstall the fuel bowl, using new
Ȭ’—œȱ˜—˜ȱ‘ŽȱŒŠ›‹ž›Ž˜›ǯȱŽŒž›Žȱ ’‘ȱ‘Žȱ˜ž›ȱ
original screws. Torque the screws to
2.5 ± 0.3 N·m (23 ± 2.6 in. lb.)ǯȱŽŽȱ’ž›ŽȱśȬŘŞǯ
Figure 5-28. Installing Fuel Bowl.
Choke Repair
1. Remove the carburetor from the engine. Discard
the old mounting gaskets for the air cleaner and
carburetor.
ȱ Řǯȱ •ŽŠ—ȱ‘ŽȱŠ›ŽŠœȱŠ›˜ž—ȱ‘ŽȱŒ‘˜”Žȱœ‘ŠĞȱŠ—ȱ‘Žȱ
self-relieving choke mechanism thoroughly.
3. Remove and discard the plastic cap from the end
˜ȱ‘ŽȱŒ‘˜”Žȱ•ŽŸŽ›Ȧœ‘ŠĞȱŠœœŽ–‹•¢ǯ
4. Note the position of the spring legs and the choke
plate for correct reassembly later. See Figure
ȱ ȱ śȬŘşǯȱŽ–˜ŸŽȱ‘Žȱ ˜ȱœŒ›Ž œȱŠĴŠŒ‘’—ȱ‘ŽȱŒ‘˜”Žȱ
™•ŠŽȱ˜ȱ‘ŽȱŒ‘˜”Žȱœ‘ŠĞǯȱž••ȱ‘Žȱœ‘ŠĞȱ˜žȱ˜ȱ‘Žȱ
carburetor body, note the preload of spring and
discard the removed parts.
Figure 5-29. Choke Details.
Retaining
Screw
Pivot
Pin