Kohler Command Pro CV980 - Manual (Page 109)

10.3
Section 10
Reassembly
10
Oil Seal
Seal depth
1.5 - 2.0 mm (0.059 - 0.078 in)
Crankcase
Surface
12.66 mm
(0.498 in.)
Crankcase Surface
Governor
Gear Shaft
Figure 10-6. Installed Main Bearing.
Install Governor Shafts, Seal, and
Governor Gear
ȱ‘Žȱ˜ŸŽ›—˜›ȱœ‘ŠĞœǰȱœŽŠ•ǰȱŠ—Ȧ˜›ȱ˜ŸŽ›—˜›ȱŽŠ›ȱ Ž›Žȱ
›Ž–˜ŸŽȱ’—ȱ’œŠœœŽ–‹•¢ǰȱ›ŽŠœœŽ–‹•ŽȱŠœȱ˜••˜ œǯ
ȱ ŗǯȱ ’‘•¢ȱ•ž‹›’ŒŠŽȱ‘Žȱ•’™ȱŠ—ȱ˜žœ’Žȱ’Š–ŽŽ›ȱ˜ȱ
‘Žȱ—Ž ȱ˜ŸŽ›—˜›ȱŒ›˜œœȱœ‘ŠĞȱœŽŠ•ȱ ’‘ȱ˜’•ǯȱ—œŠ••ȱ
‘ŽȱœŽŠ•ȱ’—˜ȱ‘ŽȱŒ›Š—”ŒŠœŽȱ˜ȱ‘ŽȱŽ™‘ȱœ‘˜ —ȱ’—ȱ
’ž›ŽȱŗŖȬŞǯȱ
Figure 10-7. Installing Governor Cross Shaft Seal.
Figure 10-8. Governor Shaft Seal Depth.
Řǯȱ ȱ‘Žȱ˜ŸŽ›—˜›ȱŽŠ›ȱœ‘ŠĞȱ Šœȱ›Ž–˜ŸŽǰȱ™›Žœœȱ˜›ȱ
•’‘•¢ȱŠ™ȱ‘Žȱ›Ž™•ŠŒŽ–Ž—ȱœ‘ŠĞȱ’—˜ȱ‘Žȱ˜’•ȱ™Š—ȱ
˜ȱŽ™‘ȱœ‘˜ —ȱ’—ȱ’ž›ŽȱŗŖȬŗŖǯ
Figure 10-9. Installed Governor Gear Shaft.
Figure 10-10. Governor Gear Shaft Press Depth.
ȱ řǯȱ ž‹›’ŒŠŽȱ‘Žȱ˜ŸŽ›—˜›ȱŒ›˜œœȱœ‘ŠĞȱ‹ŽŠ›’—ȱ
œž›ŠŒŽœȱ’—ȱ‘ŽȱŒ›Š—”ŒŠœŽȱ ’‘ȱŽ—’—Žȱ˜’•ǯȱ—œŽ›ȱ
‘ŽȱŽ—ȱ ’‘ȱ‘Žȱ̊ȱ˜›ȱ‘Žȱ˜ŸŽ›—˜›ȱŽŠ›ȱ¢˜”Žȱ
’—˜ȱ‘ŽȱŒ›Š—”ŒŠœŽȱꛜȱŠ—ȱ™˜œ’’˜—ȱœ˜ȱ‘Žȱ̊ȱ’œȱ
ȃž™ȄǯȱŽŽȱ’ž›ŽȱŗŖȬŗŗǯ
Figure 10-11. Installing Governor Cross Shaft.
Seal
Notch Main
Bearing
Governor
Gear Shaft
Governor
Cross Shaft