ADLINK aTCA-N700 - Manual (Page 57)

aTCA-N700 HW Users Guide
５７
VJTAG M19 VJTAG I JTAG Power
VPP M21 VPUMP I
Ethernet Interface
MAC_MDC_IO48RSB4V0
AA3 RMII_MDC O PHY Management Clock
MAC_MDIO_IO49RSB4V0 V4 RMII_MDIO I/O PHY Management Data
MAC_CRSDV_IO51RSB4V0 W4 RMII_CRS_DV I RMII Data Valid
MAC_RXER_IO50RSB4V0 AA4 RMII_RX_ER I RMII Rx Error
MAC_TXEN_IO52RSB4V0 Y4 RMII_TX_EN0 O RMII TX Enable
MAC_TXD_0_IO56RSB4V0 AA5 RMII_TXD0 O RMII TX DATA0
MAC_TXD_1_IO55RSB4V0 W5 RMII_TXD1 O RMII TX DATA1
MAC_RXD_0_IO54RSB4V0 V5 RMII_RXD0 I RMII RX DATA0
MAC_RXD_1_IO53RSB4V0 U5 RMII_RXD1 I RMII RX DATA1
MAC_CLK T6 RMII_REF_CLK I RMII Reference Clock
UART Interface
UART_0_TXD_GPIO_20 Y22
DBG_TXD O IPMC Console for Debug
UART_0_RXD_GPIO_29 U18 DBG_RXD I
UART_1_TXD_GPIO_28 V20 PAYLD_TXD O
UART_1_RXD_GPIO_29 W22 PAYLD_RXD I
CPU & IPMC
Communication for payload
data
Reserved GPIOs
GPIO_11_IO57RSB4V0
T4 Connected to CPLD I/O IPMC_GPIO11
GPIO_12_IO37RSB4V0 AA2 Connected to CPLD I/O IPMC_GPIO12
GPIO_13_IO36RSB4V0 AB2 Connected to CPLD I/O IPMC_GPIO13
GPIO_14_IO35RSB4V0 AB3 Connected to CPLD I/O IPMC_GPIO14
GPIO_15_IO34RSB4V0 Y3 Connected to CPLD I/O IPMC_GPIO15
FPGA GPIOs
GFA2_IO68PDB5V0 E3
IPMC_CLK1 I FPGA Clock
GCB0_IO27NDB1V0 H22 IPMC_FPGA_LB_nRST I FPGA Reset
IPMC Mode
GFC2_IO67PPB5V0 E1
J6(Pull up & Pull down
jump)
I
IPMC MODE SELECT
0 : Stand-alone mode
1 : Shelf mode
HOT SWAP
EMC_AB_0_IO04NDB0V0 A8
E_HANDLE(Base Hot
swap switch pin)
I
Hot-swap Handle switch
0 : Hot-swap Handle closed
1 : Hot-swap Handle open
Payload RESET Control
EMC_AB_5_IO06PDB0V0 E12
COLD_RST_B(Cold
reset command)
O
Payload will be reset.
0 : Reset
1 : Normal operation
GFB0_IO65NDB5V0 G2
IPMC_PUSH_RESET_L
(Push button switch)
I
Reset request from Push
Button
0 : Reset detect
1 : Normal operation
GCA0_IO28NDB1V0 J19
P20_HRST_REQ_N(Co
nnected from P2041)
I
Reset request from LMP
0 : Reset detect
1 : Normal operation
Slot ID
EMC_AB_19_IO13PDB0V0 B17
HA0 to ZONE1(Power
connector)
I ATCA Slot ID0
EMC_DB_13_GAC2_IO70P
DB5V0
D3
HA1 to ZONE1(Power
connector)
I ATCA Slot ID1
EMC_CS0_N_GAB0_IO01N
DB0V0
A5
HA2 to ZONE1(Power
connector)
I ATCA Slot ID2
EMC_AB_6_IO07NDB0V0 B12
HA3 to ZONE1(Power
connector)
I ATCA Slot ID3
EMC_BYEN_0_GAC0_IO02
NDB0V0
B9
HA4 to ZONE1(Power
connector)
I ATCA Slot ID4
GFB2_IO68NDB5V0 F3
HA5 to ZONE1(Power
connector)
I ATCA Slot ID5
EMC_DB_9_GEC1_IO63PD
B5V0
G3
HA6 to ZONE1(Power
connector)
I ATCA Slot ID6
GFB1_IO65PDB5V0 F1
HA7 to ZONE1(Power
connector)
I ATCA Slot ID7
Module Control
EMC_DB_6_GEB0_IO62ND
B5V0
J1 RTM_INSERT I
RTM Present
0 : Insert
1 : Extract
EMC_AB_10_IO09NDB0V0 D11 RTM_ENABLE O
RTM Module Enable
0 : Enable