Compliance statements, Red dsmc operation guide – RED DSMC User Manual

Page 4

RED DSMC OPERATION GUIDE

955-0020_V5.3, REV-J | 4

COMPLIANCE STATEMENTS

INDUSTRIAL CANADA EMISSION COMPLIANCE STATEMENTS

This device complies with Industry Canada license-exempt RSS

standards RSS 139 and RSS 210. Operation is subject to the follow-

ing two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference

that may cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
Le présent appareil est conforme aux CNR d’Industrie Canada ap-

plicables aux appareils radio exempts de licence. L’exploitation est

autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas

produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter

tout brouillage radioélectrique subi, même si le brouillage est sus-

ceptible d’en compromettre le fonctionnement.Cet appareil numéri-

que de la classe B est conforme à la norme NMB-003 du Canada.

FEDERAL COMMUNICATIONS COMMISSION (FCC) STATE-

MENTS

This equipment has been tested and found to

comply with the limits for a Class B digital de-

vice, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reason-

able protection against harmful interference

in a residential installation. This equipment

generates, uses and can radiate radio fre-

quency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference

to radio communications. However, there is no guarantee that inter-

ference will not occur in a particular installation. If this equipment

does cause harmful interference to radio or television reception,

which can be determined by turning the equipment off and on, the

user is encouraged to try to correct the interference by one or more

of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

Consult the dealer or an experienced radio/TV technician for

help.

In order to maintain compliance with FCC regulations, shielded

cables must be used with this equipment. Operation with non-ap-

proved equipment or unshielded cables is likely to result in interfer-

ence to radio and TV reception. The user is cautioned that changes

and modifications made to the equipment without the approval of

manufacturer could void the users authority to operate this equip-

ment.
NOTE: This device complies with Part 15 of the FCC Rules.
Operations subjected to the following two conditions (1) this device

may not cause harmful interference, and (2) this device must accept

any interference received, including that may cause undesirable in-

terference.

CAUTION: Exposure to Radio Frequency Radia-

tion.

The device shall be used in such a manner that the potential for hu-

man contact is minimized
This equipment complies with FCC radiation exposure limits set

forth for an uncontrolled environment. This equipment should be

installed and operated with a minimum distance of 20 cm between

the radiator and your body.

CAUTION: Regulations of the FCC and FAA

prohibit airborne operation of radio-frequency

wireless devices because there signals could

interfere with critical aircraft instruments.

CAUTION: If the device is changed or modified

without permission from RED, the user may

void his or her authority to operate the equip-

ment.

AUSTRALIA AND NEW ZEALAND STATEMENTS

RED declares that the radio equipment described in this document

comply with the following international standards.

IEC 60065 - Product Safety

ETSI EN 300 328 - Technical requirement for radio equipment

RED declares digital devices described in this document comply

with the following Australian and New Zealand standards.

AS/NZS CISPR 22 – Electromagnetic Interference

AS/NZS 61000.3.2 – Power Line Harmonics

AS/NZS 61000.3.3 – Power Line Flicker

JAPAN STATEMENTS

This is a Class B product based on the

standard of the Voluntary Control Council

for Interference (VCCI) for information tech-

nology equipment. If this equipment is used

near a radio or television receiver in a do-

mestic environment, it may cause radio in-

terference. Install and use the equipment

according to the instruction manual.

EUROPEAN UNION COMPLIANCE STATEMENTS

RED declares that the radio

equipment described in this

document comply with the

R&TTE Directive (1999/5/

EC) issued by the Commis-

sion of the European Com-

munity.

Compliance with this directive implies conformity to the following

European Norms (in brackets are the equivalent international stan-

dards).

EN 60065 (IEC 60065) – Product Safety

ETSI EN 300 328 Technical requirement for radio equipment

ETSI EN 301 489 General EMC requirements for radio equip-

ment.