HP MPX200 Multifunction Router - Manual (Page 127)

Table 9 MPX200 Router log messages (continued)
Description
Msg
type Module
type
Log message ID
iSCSI processor failed the internal
loopback test. Error iSCSI #%d: QLRunDiag: MBOX Diag test
internal loopback failed %x %x
74056
iSCSI processor failed the external
loopback test. Error iSCSI #%d: QLRunDiag: MBOX Diag test
external loopback failed %x %x
74057
iSCSI processor reported an invalid
ATIO Continuation type x. Error iSCSI #%d: QLUtmReceiveScsiCmd: Invalid ATIO
Continuation type %x
74068
iSCSI processor reported an
Immediate data address Error iSCSI #%d: QLUtmProcessResponseQueue:
Immediate data addr %08x:%08x in
unsupported PduType
74069
(xxxxxxxx:xxxxxxxx) in an
unsupported PDU Type.
iSCSI processor could not connect
with the iSNS. Error iSCSI #%d: QLiSNSEnableCallback: iSNS Server
TCP Connect failed
74241
iSCSI processor reported that the
iSCSI port NVRAM contains invalid
data (checksum error). Error iSCSI #%d: QLIsrDecodeMailbox: NVRAM invalid 74577
iSCSI processor reported a duplicate
IP address was detected (address
xxxx xxxx xxxx xxxx xxxx). Error iSCSI #%d: QLIsrDecodeMailbox: AEN %04x,
Duplicate IP address detected, MB[1-5]
%04x %04x %04x %04x %04x
74580
iSCSI processor reported a link down
condition. Error iSCSI #%d: QLIsrDecodeMailbox: Link down 74587
Driver failed to receive a heartbeat
from the iSCSI processor for the
specified number of seconds. Error iSCSI #%d: QLReadyTimer: Adapter missed
heartbeat for %d seconds. Time left %d
74656
iSCSI processor (adapter) failed to
provide a heartbeat for x seconds. Error iSCSI #%d: QLReadyTimer: Adapter missed
heartbeat for 0x%x seconds
74659
iSCSI processor failed to complete
an abort request. Error iSCSI #%d: QLReadyTimer: Abort pTpb=%p
failed, DrvCount 0x%x
74660
Driver timed out an iSCSI processor
operation and is aborting the
operation. Error iSCSI #%d: QLTimer: Abort pTpb=%p, Type %x,
Timeout 0x%x DrvCount 0x%x, DdbIndex
0x%x
74661
Driver timed out an iSCSI processor
mailbox command. Error iSCSI #%d: QLReadyTimer: MBOX_CMD %04x %04x
%04x %04x %04x %04x %04x %04x timed
out
74663
Driver timed out while attempting to
reconnect with the iSNS. Error iSCSI #%d: QLReadyTimer: QLiSNSReenable
failed
74665
iSCSI processor was restarted. Error iSCSI #%d: QLProcessSystemError: Restart
RISC
74705
iSCSI processor rejected the firmware
initialize command. Error iSCSI #%d: QLInitializeFW:
MBOX_CMD_INITIALIZE_FIRMWARE failed
%04x %04x %04x %04x %04x %04x
74746
Driver’s initiator database is full. The
driver is capable of storing 1024 Error iSCSI #%d: QLUpdateInitiatorData: No more
room in Initiator Database.
74784
iSCSI initiators in its database. Use
the CLI or GUI to remove
unwanted/unused iSCSI initiators.
Driver’s target database is full. Use
the CLI or GUI to remove
unwanted/unused iSCSI targets. Error iSCSI #%d: QLSetTargetData: No more room in
Target Database.
74800
127