KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 4.00 to 4.xx - Manual (Page 78)

B-10
SERIES EL 071414
B.50 [SOURce:]RESistance:TRANsient COMMAND 
RES:TRAN
Syntax: Short Form: [SOUR:]RES:TRAN ,,,
Long Form: [SOURce:]RESistance:TRANsient ,,,
Where:
= = the maximum resistance value of the transient (Ohms)
= = time (Seconds) from start to end of transient (0.0005 Second minimum)
= = number of times transient is to be repeated (default = 1, maximum = 65,000)
(optional) = = total time (Seconds) of repeating pulse train (must be at least 0.0005
greater than transient )
Description: Configures a transient resistance pulse that is initiated by SYST:MODE:TRAN (see PAR. B.100).
See PAR. B.106 for details on using both Transient and Ramp commands at the same time. Figure B-
1 on page B-18 shows transient and ramp timing.
B.51 [SOURce:]RESistance:TRANsient? QUERY 
RES:TRAN?
Syntax: Short Form: [SOUR:]RES:TRAN?
Long Form: [SOURce:]RESistance:TRANsient?
Returns: ,,, (see PAR. B.50 for definitions.)
Description:Returns the transient resistance pulse parameters established by RES:TRAN (see PAR. B.50).
B.52 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude] COMMAND 
VOLT
Syntax: Short Form: [SOUR:]VOLT[:LEV][:IMM][:AMP]
Long Form: [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]
where: = voltage setpoint
Description: Establishes voltage setpoint. The voltage setpoint only affects the load when the load is in Voltage
mode of operation. Voltage setpoint is stored in non-volatile memory; value is restored upon power-up.
B.53 [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]? QUERY 
VOLT?
Syntax: Short Form: [SOUR:]VOLT[:LEV][:IMM][:AMP]?
Long Form: [SOURce:]VOLTage[:LEVel][:IMMediate][:AMPlitude]?
Returns: = voltage setpoint
Description: Indicates voltage setpoint.
B.54 [SOURce:]VOLTage:PROTection:OVER COMMAND 
VOLT:PROT:OVER
Syntax: Short Form: [SOUR:]VOLT:PROT:OVER
Long Form: [SOURce:]VOLTage:PROTection:OVER
where = overvoltage protection limit
Description: Sets overvoltage protection limit. Overvoltage protection setpoint is stored in non-volatile memory;
value is restored upon power-up.
B.55 [SOURce:]VOLTage:PROTection:OVER? QUERY 
VOLT:PROT:OVER?
Syntax: Short Form: [SOUR:]VOLT:PROT:OVER?
Long Form: [SOURce:]VOLTage:PROTection:OVER?
Returns = overvoltage protection limit
Description: Indicates overvoltage protection limit.
B.56 [SOURce:]VOLTage:PROTection:OVER:STATe[:LEVel] COMMAND

VOLT:PROT:OVER:STAT 0
Syntax: Short Form: [SOUR:]VOLT:PROT:OVER:STAT[:LEV] 0
Long Form: [SOURce:]VOLTage:PROTection:OVER:STATe[:LEVel] 0
Description: Clears overvoltage protection error.