KEPCO EL Series Electronic Load Operator Manual P/N 243-1295 Firmware Version 4.00 to 4.xx - Manual (Page 5)

SERIES EL 020498
iii
TABLE OF CONTENTS
SECTION PAGE
3.15.1 Ramp Details........................................................................................................................................... 3-24
3.15.2 Ramp Interactions ................................................................................................................................... 3-25
3.15.3 Accessing Ramps from the Front Panel .................................................................................................. 3-25
3.16 Minimum Input Voltage ............................................................................................................................... 3-26
3.16.1 Programming Minimum Input Voltage from the Front Panel ................................................................... 3-26
3.17 Analog Programming .................................................................................................................................. 3-27
3.18 Operator Maintenance ................................................................................................................................ 3-27
APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
A.1 Introduction ................................................................................................................................................ A-1
A.2 *CLS — Clear Status Command ............................................................................................................... A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................... A-1
A.4 *ESE? — Standard Event Status Enable Query........................................................................................ A-2
A.5 *ESR? — Event Status Register Query..................................................................................................... A-2
A.6 *IDN? — Identification Query..................................................................................................................... A-2
A.7 *OPC — Operation Complete Command .................................................................................................. A-3
A.8 *OPC? — Operation Complete Query ....................................................................................................... A-3
A.9 *RST — Reset Command.......................................................................................................................... A-3
A.10 *SRE — Service Request Enable Command ............................................................................................ A-4
A.11 *SRE? — Service Request Enable Query ................................................................................................. A-4
A.12 *STB? — Status Byte Register Query ....................................................................................................... A-4
A.13 *WAI — Wait Command ............................................................................................................................ A-4
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ................................................................................................................................................ B-1
B.2 Numerical Values and Data Conventions .................................................................................................. B-2
B.3 DIAGnostic:RESet Command.................................................................................................................... B-2
B.4 DIAGnostic:TREE:DISPlay Command ...................................................................................................... B-2
B.5 DIAGnostic:TREE:SEParator Command................................................................................................... B-3
B.6 DIAGnostic:TREE:SEParator? Query........................................................................................................ B-3
B.7 LOCK Command ....................................................................................................................................... B-3
B.8 LOCK? Query ............................................................................................................................................ B-3
B.9 [SOURce:]INPut[:STATe] Command ......................................................................................................... B-3
B.10 [SOURce:]INPut[:STATe]? Query .............................................................................................................. B-3
B.11 [SOURce:]INPut:CUToff:TIME Command ................................................................................................. B-3
B.12 [SOURce:]INPut:CUToff:TIME? Query ...................................................................................................... B-4
B.13 [SOURce:]INPut:CUToff:VOLTage Command ........................................................................................... B-4
B.14 [SOURce:]INPut:CUToff:VOLT? Query ..................................................................................................... B-4
B.15 INPut:RAMP Command............................................................................................................................. B-4
B.16 INPut:RAMP? Query.................................................................................................................................. B-5
B.17 [SOURce:]INPut:PROTection:CLEar Command........................................................................................ B-5
B.18 [SOURce:]INPut:PROTection:SHORt[:STATe] Command......................................................................... B-5
B.19 [SOURce:]OUTPut[:STATe] Command ..................................................................................................... B-5
B.20 [SOURce:]OUTPut[:STATe]? Query .......................................................................................................... B-5
B.21 [SOURce:]OUTPut:PROTection:CLEar Command.................................................................................... B-5
B.22 [SOURce:]OUTPut:PROTection:SHORt[:STATe] Command..................................................................... B-5
B.23 [SOURce:]MEASure:ALL? Query .............................................................................................................. B-6
B.24 [SOURce:]MEASure:ALL2? Query ............................................................................................................ B-6
B.25 [SOURce:]MEASure[:SCALar]:CURRent[:DC]? Query ............................................................................. B-6
B.26 [SOURce:]MEASure[:SCALar]:POWer[:DC]? Query ................................................................................. B-6
B.27 [SOURce:]MEASure[:SCALar]:VOLTage[:DC]? Query.............................................................................. B-6
B.28 [SOURce:]CONDuctance[:LEVel][:IMMediate][:AMPlitude] Command ..................................................... B-6
B.29 [SOURce:]CONDuctance[:LEVel][:IMMediate][:AMPlitude]? Query .......................................................... B-6