Paradyne COMSPHERE 3611 - Manual (Page 79)

COMSPHERE 3600 Series Data Service Units
Index-2 September 1996 3610-A2-GB48-50
digital test (DT), 3-9
DrBU, Backup menu, 3-6
DSD
Async Diff message, D-2
verify port interface, 2-1
Wrong RTS message, D-2
DSR FrcOn
for digital bridging, 4-17
for TDM/MCMP, 4-14
DSR on Tst
for digital bridging, 4-17
for TDM/MCMP, 4-14
DSU
Agg Exceeded message, D-3
DTE connections, 2-5
front panels, 3-2
how to open, 2-2
power-up routine, 2-5
reassembling, 2-4
separating from TDM or MCMP, 2-3
status indicators, 3-3
Undersp Reqd message, D-3
with digital bridge capability, 1-3
with LPDA-2 Interoperability, 1-4
with MCMP capability, 1-3
with TDM capability, 1-2
DSU operation. See 3610-A2-GB46
DTE connections, 2-5
DTE Port
for digital bridging, 4-18
for TDM/MCMP, 4-15
DTR Alarm, 4-16
for TDM/MCMP, 4-13
E
EBrdg, configuration example, C-6
EIA-232 interface, changing to V.35, 2-2, 2-4–2-6
Elast Stor
for digital bridging, 4-16
for TDM/MCMP, 4-13
Not Valid message, D-3
Elastic Store, 1-1
End-to-End test (EE), 3-9
ExtendChan
for digital bridging, 4-17
for TDM/MCMP, 4-14
extended bridge, 3-6
EBrdg, 1-2–1-3
external leads, 3-12
F
Fac, factory default settings, A-4
faceplate, 3-2
factory defaults. See 3610-A2-GB46 & 3610-A2-GB49
features
common, 1-1
MCMP specific, 1-3
TDM specific, 1-2
FEP
&ShrDv Incmpt message, D-3
Async Diff message, D-3
port sharing, 1-1
Prt Underspd message, D-3
Speeds diff message, D-3
flat cables, 2-3
front panels, 3-2
G
G2Trib Inv MCMP, message, D-3
I
Identity, 3-5
in-band framing, 1-2
Incmpt Diag Mode, message, D-3
indicators, status, 3-3
installation procedures
changing hardware straps, 2-1
how to open the DSU, 2-2
installing the DSU, 2-1
installing the power cable, 2-4
pre-installation notes, 2-1
Inval
BridgeRate message, D-3
DSU Timing message, D-4
lowest Prt message, D-4
M-Pt Confg message, D-4
Port Cntrl message, D-4
Invalid
Async message, D-4
Port Spd message, D-4
Underspeed Port message, D-5
L
LEDs, 3-12
Link Problem Determination Aid. See LPDA-2
Local branch, 3-4
loopbacks, 3-8
digital, 3-8
remote digital, 3-8
Lowest Port#
for digital bridging, 4-10
for MCMP Setup, 4-3, 4-4
for TDM Setup, 4-6, 4-7
LPDA-2, with TDM or MCMP, 1-4