Paradyne COMSPHERE 3611 - Manual (Page 62)

Configuration Worksheet for Bridge Mode (2 of 2)
DSU
Configuration
Options
Value
Rate(Kbps) z Auto, 64CC, 64L, 56, 38.4, 19.2, 9.6, 4.8,
2.4
TxClkSource z Int, RXC, DDS, Prt1
Msg Clamp z A Enab, Disab
TxElasStor Enab, Disab
RxElasStor z A Enab, Disab
19.2 PowrLvl FF A +6, 0, –10
64KScrambling A On, Off
64KLatchLpbk A On, Off
Net I Timing z}}} A Int, Net I , Prt1, Prt2, Prt3, Prt4, Prt5, Prt6
V.54 Lpbk A Enab, Disab
Diagnostic DSU
Configuration
Options
Value
Diag Type NonD z , Disr, Mixed z , None
2nd Ch(bps) z A 100, 400, 800, 1200, 1600
Disr Type 3600s z , 3600e, Br56
Diagnostic General
Configuration
Options
Value
Position Cntrl
LinkConfig Pt-Pt, M-Pt
Resp Period A 1, 2, 10
Trib TimOut A min and sec (5 sec to 10 min)
Diag Conn CC, DC
Link Delay A 0s, 1s, 2s, 5s, 10s, 20s, 50s
Network Delay A 0s, 1s, 2s, 5s, 10s, 20s, 50s
Packet Delay A 0s, 1s, 2s, 5s
M-PtSymPrt H A Enab, Disab
Fast Sel A Enab, Disab
General
Configuration
Options
Value
DTE Port :: EIA232, V.35
RTS Cntrl FrcOn
CTS Cntrl Std, =RTS
LSD Lead A STD, Delay, FrcOn
CTS Lead A STD, Delay, FrcOn
SystemStat A Enab, Disab
Circ Assur A Enab, Disab
Tst Pattern A AT&T, Std
RespondRDL A Enab, Disab
LL by DTE A Enab, Disab
RL by DTE A Enab, Disab
Bilat Lpbk A Enab, Disab
Ext Leads A ExtLd, Rate, RPowr
CCN by EL A Enab, Disab
DTR Alarm A Enab, Disab
SW Vers A 3.24, 4.43, 6.66, Normal
AnswExtBU A Enab, Disab
Async → Sync z Enab, Disab
AsyncBit/Char z 6, 7, 8, 9, 10
Stop Bits z 1, 2
Overspeed z 1.0, 2.3
PowerOnTst Enab, Disab
ChgMd
Configuration
Options
Value
Protocol Mode DPII, ADp
LPDA-2
Configuration
Options
Value
LPDA-2 Enab, Disab
LPDA Address 1–256
SNA Backup Enab, Disab
Code 1 (6 digits)
Code 2 (7 digits)
S1 Hardware
Settings
Value
DBM Interface LLL Permissive (ON), Programmable (OFF)
Frame Ground/
Signal Ground Connected (ON), Disconnected (OFF)
EIA-232 Test Mode Enable (ON), Disable (OFF)
V.35 Test Mode Enable (ON), Disable (OFF)
z Does not appear for EBrdg
FF 19.2 Power Level defaults to +6 dB when ID App Module
displays XLOOP
}}} Ports 3–6 not available for 2-port Flex MUX models
H TDM option only
:: Appears when non-Flex MCMP or non-Flex TDM is
installed or a 6-port MCMP/Flex or TDM/Flex is installed
with DSU firmware version less than 6.33
L LL V.32 Analog DBM only
n = Port number
SS.S = Aggregate rate
A Configuration options that do not appear when Full mode is
disabled using Menu from the Configuration branch.