KORG Krome music workstasion 61key - Manual (Page 114)

Adjusting Global KROME setings
110
Curve 9 is designed specifically for playing piano
sounds from the weighted NH keyboards in the 73‐
note and 88‐note models.
For details on the other curves, see the graphic below,
as well as the “Velocity Curve” section on page 194 of
the Parameter Guide.
3. Specify the position where the velocity curve will
be applied. For more about “Convert Position,”
please see “Transposing the keyboard,” above.
Velocity curves
Bypassing the effects
You can bypass the KROME’s insert effects, master
effects, and total effects. These settings will bypass the
effects in all modes. If you’re using effects such as
reverb or chorus provided by an external effect
processor, mixer, or DAW, you can bypass the
KROME’s own effects so that they will not be used.
1. Access the Global mode P0: Basic Setup– Basic
page.
2. Use the various Effect Global SW buttons to select
the effects that you want to bypass. The effect will
be bypassed if the check box is cleared.
Clearing the “IFX 1‐5” box: Bypasses the insert effects
Clearing the “MFX 1&2” box: Bypasses the master
effects
Clearing the “TFX 1&2” box: Bypasses the total effects
“MFX1&2” and “TFX” can also be controlled by the
front panel MASTER FX button and TOTAL FX button.
This is convenient when you want to temporarily turn
off these effects during a performance.
Note: These parameters will always be turned on when
the KROME starts up.
Arpeggiator recall settings (Linking
the arpeggiator with programs or
combinations)
You can specify whether the arpeggiator settings
written into each program or combination will also be
selected when you select that program or combination,
or whether the arpeggiator will stay in its current state
without changing settings.
With the factory settings, the former will occur. You
can choose the latter behavior if you want to play
phrases and patterns with certain arpeggiator settings
while you switch only the sound between different
programs or combinations.
1. Access the Global mode P0: Basic Setup– Basic
page.
2. In the “Load ARP when changing” area, if the
“Program” or “Combination” box is selected,
switching programs or combinations respectively
will recall the arpeggiator settings written in that
program or combination.
Disabling the arpeggiator and drum
track
1. Access the Global mode P0: Basic Setup– Basic
page.
2. If the “All ARP/DT Off” box is selected, all
arpeggiator and drum track functionality will be
turned off.
Even if the ARP or DRUM TRACK buttons are on, the
arpeggiator and drum track will not function.
Recalling the last-selected mode and
page at power-on
1. Access the Global mode P0: Basic Setup– System
Preferences page.
2. If the Power‐On Mode is set to Reset (factory
setting), KROME will automatically select the
Program mode P0: Play.
If the Power On Mode is set to Memorize, the location
(mode and page) and the program or combination
number that had been selected when you turned off
the power will be recalled.
Enabling a beep tone when the
display is pressed
1. Access the Global mode P0: Basic Setup– System
Preferences page.
2. If the “Beep Enable” check box is selected, a beep
tone will sound when you press an object in the
display. Clear the check box if you don’t want a
beep to sound.
Protecting the memory
1. Access the Global mode P0: Basic Setup– System
Preferences page.
2. If a Memory Protect check box is selected, the
corresponding write, data load, or song recording
operation will be disabled, thus protecting the
contents of memory.
1
MAX
127
1
8
6
5
4
3
2
7
Soft
127
Strong
1
1
2
3
8
6
5
4
7
9
9
Velocity (MIDI In to sound engines) Velocity (Keyboard to MIDI Out)
Convert Position = PostMIDI Convert Position = PreMIDI
Velocity
effect
Select the
mode that is
selected at
power-on
Beep setting
Memory
protect
settings