Extron electronic VGA MATRIX SWITCHERS MVX PLUS 128 - Manual (Page 86)

SIS ™ Programming and Control, cont’d
MVX Plus 128 VGA Matrix Switchers • Programmer’s Guide 4-16
PRELIMINAR
Y
Command/Response Table for IP SIS Commands
Symbol defi nitions
X3)
= Matrix name (Up to 240 alphanumeric characters)
N The following characters are invalid in the name: {space} ~ , @ = ` [ ] { } < > ‘ “ ; : | \ and ?.
X3!
= Default name CP-300-450-MAV-- + last 3 pairs of MAC address
X3@
= Time and date (for set) In the format: MM/DD/YY
•
HH:MM:SS where:
MM = month: 01 (January) through 12 (December)
DD = 01 through 31
YY = 00 through 99
HH = 00 through 24
MM = 00 through 59
SS = 00 through 59
X3#
= Time and date (for read) In the format: Day,•DD•Mmm
•
YYYY•HH:MM:SS where:
Day = weekday: Mon through Sun
DD = 01 through 31
Mmm = month: Jan through Dec
YYYY = 2000 through 2099
HH = 00 through 24
MM = 00 through 59
SS = 00 through 59
X3$ = GMT offset –12.0 through +14.0. Hours and minutes removed from GMT
X3%
= Daylight Savings Time 0 = Daylight Savings Time off/ignore
1 = Daylight Savings Time on (northern hemisphere)
2 = Daylight Savings Time on (Europe)
3 = Daylight Savings Time on (Brazil)
X3^
= IP address ###.###.###.###
X3&
= Hardware (MAC) address ##-##-##-##-##-##
X3* = Number of open connections 0 - 255
X3(
= Password 12 alphanumeric characters
N The following characters are invalid in passwords: {space} + ~ , @ = ` [ ] { } < > ‘ “ ; : | \ and ?.
X4)
= Domain name Standard domain name rules apply (for example: [email protected])
N The following characters are invalid in a domain name: {space} + ~ , = ` [ ] { } < > ‘ “ ; : | \ and ?. The @ character is acceptable only as
the lead-in to the domain name (such as @extron.com).
X4!
= E-mail account 65 - 72. 65 = e-mail recipient 1, 66 = 2, 67 = 3, ... 72 = recipient #8
X4@ = E-mail address Typical e-mail address format (for example: [email protected])
X4#
= Notify when? 0 = no response 2 = fi xed/restored
1 = fail/missing 3 = both 1 & 2
X4$
= Notifi cation selections 01 through 12 = input 1 through input 12
13 through 16 = not used
17 = power supply
X4%
= Notify status (for read) 17-digit number. For each digit: 0 = do not notify, 1 = notify
X4^
= DHCP 0 =1 off, 1 = on
X4&
= Port # 00 through 99 (00 = all ports)
X4*
= Baud rate 9600, 19200, 38400, 115200
X4( = Parity o dd, even, none, mark, space (only fi rst letter required)
X5)
= Data bits 7, 8
X5!
= Stop bits 1, 2
X5@
= Port type 0 = RS-232
1 = RS-422
2 = RS-485
X5# = Verbose mode 0 = clear/none (default for Telnet connection)
1 = verbose mode (default for RS-232/RS-422 connection)
2 = tagged responses for queries
3 = verbose mode and tagged for queries
N If tagged responses is enabled, all read commands return the constant string and the value as the set command does
(for example, the read matrix name command
E
CN
}
, returns Ipn
•X3)]
).
X5$
= RAM status 0 = RAM dirty (needs saving to fl ash memory)
1 = RAM has been saved (ok to power off/reset)