KEPCO KLP Series (older -1200 models) Operator Manual - Manual (Page 91)

KLP 073008
B-5
B.17 [SOURce:]LIST:CURRent? QUERY
LIST:CURR?
Syntax: Short Form: LIST:CURR? Long Form: LIST:CURRent?
Return Value: , , . . . to
Description: Identifies the parameters (main channel) entered for the list. Starting at location established by
LIST:QUERy, returns comma-separated list of up to 16 values indicating the main channel parameters
entered. i.e., the contents of main channel List Data Table. Related Commands: LIST: CURR,
LIST:QUERy. If LIST:VOLT has any entries, an error message: -221,"Settings conflict" is posted in the
error queue. (See example, Figure B-2.)
B.18 [SOURce:]LIST:CURRent:POINts? QUERY
LIST:CURR:POIN?
Syntax: Short Form: LIST:CURR:POIN? Long Form: LIST:CURRent:POINts?
Return Value: (0 to 1001)
Description: Identifies the total number of points in a list and the next location to be filled by LIST:CURR
command. The LIST:CURR pointer is initially at 0 via LIST:CLE. For each data point entered by a
LIST:CURR command the list pointer is incremented If LIST:CURR:POIN? returns 5, the LIST:CURR
pointer is at 5 indicating there are 6 data points comprising the list. If LIST:VOLT has any entries, an
error message: -221,"Settings conflict" is posted in the error queue.Related Commands: LIST:CURR.
(See example, Figure B-2.)
B.19 [SOURce:]LIST:DIRection COMMAND
LIST:DIR
Syntax: Short Form: LIST:DIR (UP|DOWN) Long Form: LIST:DIRection (UP|DOWN)
Description: Allows the list to be executed from beginning to end (UP) or from end to the beginning
(DOWN). *RST or LIST:CLEar sets the list to the UP direction (beginning to end). Works with both
LIST:GEN DSEQ and LIST:GEN SEQ commands. Related Commands: LIST:GEN. LIST:SEQ,
LIST:DWEL?. (See example, Figure B-2.)
B.20 [SOURce:]LIST:DIRection? QUERY
LIST:DIR?
Syntax: Short Form: LIST:DIR? Long Form: LIST:DIRection?
Return Value: (UP or DOWN)
Description: Identifies the for executing the list established by LIST:DIR. Related Commands: LIST: DIR. (See
example, Figure B-2.)
B.21 [SOURce:]LIST:DWELl COMMAND
LIST:DWEL
Syntax: Short Form: LIST:DWEL (0.010 to 655.35),,, . . . to maximum of 100 values
Long Form: LIST:DWELl (0.010 to 655.35),,, . . . to maximum of 100 values
Description: Determines how long the main channel parameters will be active. Sets time value (from 0.010 to
655.35) in seconds for List:Dwell locations of the List Data Table. The main channel (either voltage or
current) is determined by the load. If LIST:DWEL is entered for only location 0, that time duration will
apply to all steps when either VOLT:MODE LIST or CURR:MODE LIST is executed. Related Com-
mands: VOLT:MODE, LIST:CURR, LIST:VOLT, LIST:DWEL?, LIST:SEQ. (See example, Figure B-2.)
B.22 [SOURce:]LIST:DWELl? QUERY
LIST:DWEL?
Syntax: Short Form: LIST:DWEL? Long Form: LIST:DWELl?
Return Value:
Description: Identifies the dwell times entered for the list. Starting at location established by LIST:QUERy,
returns comma-separated list of up to 16 values indicating the dwell time parameters entered. i.e., the
contents of LIST:DWEL locations of the List Data Table. Related Commands: LIST: DWEL,
LIST:QUERy. (See example, Figure B-2.)
B.23 [SOURce:]LIST:DWELl:POINts? QUERY
LIST:DWEL:POIN?
Syntax: Short Form: LIST:DWEL:POIN? Long Form: LIST:DWELl:POINts?
Return Value: (0 to 1001)
Description:Identifies the number of locations for which time values have been entered and the next loca-
tion to be filled by a LIST:DWEL command. If LIST:DWEL:POIN? returns 6, dwell times have been
entered for locations 0 through 5 and location 6 is the next to be filled by a LIST:DWEL command.
LIST:DWEL, LIST:DWEL:POIN. (See example, Figure B-2.)