KEPCO KLP Series (older -1200 models) Operator Manual - Manual (Page 7)

KLP SVC 020498
i
TABLE OF CONTENTS
SECTION PAGE
SECTION 1 - INTRODUCTION
1.1 Scope of Manual......................................................................................................................................... 1-1
1.2 General Description .................................................................................................................................... 1-1
1.3 Specifications.............................................................................................................................................. 1-1
1.4 Features...................................................................................................................................................... 1-8
1.4.1 Local Control ........................................................................................................................................... 1-8
1.4.2 Remote Control ....................................................................................................................................... 1-8
1.4.2.1 Digital Programming........................................................................................................................... 1-8
1.4.2.2 Analog Programming ......................................................................................................................... 1-8
1.4.3 Digital Calibration .................................................................................................................................... 1-8
1.4.4 Overvoltage/Overcurrent Protection........................................................................................................ 1-9
1.4.5 User-defined Voltage/Current Limits (Virtual Models) ............................................................................. 1-9
1.4.6 Storage of User-Programmed Active Settings ........................................................................................ 1-9
1.4.7 User-Programmed Sequences................................................................................................................ 1-9
1.4.8 Last Setting Recall .................................................................................................................................. 1-9
1.4.9 Built-in Protection .................................................................................................................................... 1-9
1.4.10 Internal Relay .......................................................................................................................................... 1-10
1.4.11 Master/Slave Control............................................................................................................................... 1-10
1.5 Equipment Supplied.................................................................................................................................... 1-10
1.6 Accessories ................................................................................................................................................ 1-10
1.7 Safety.......................................................................................................................................................... 1-10
SECTION 2 - INSTALLATION
2.1 Unpacking and Inspection .......................................................................................................................... 2-1
2.2 Terminations and Controls.......................................................................................................................... 2-1
2.2.1 Front Panel Controls and Indicators........................................................................................................ 2-1
2.2.2 Rear Panel Connectors and Switch. ....................................................................................................... 2-1
2.3 Source Power Requirements...................................................................................................................... 2-5
2.4 Cooling........................................................................................................................................................ 2-5
2.5 Preliminary Operational Check ................................................................................................................... 2-5
2.6 Installation................................................................................................................................................... 2-6
2.6.1 Rack Mounting ........................................................................................................................................ 2-6
2.7 Wiring Instructions ...................................................................................................................................... 2-6
2.7.1 Safety Grounding .................................................................................................................................... 2-7
2.7.2 Source Power.......................................................................................................................................... 2-7
2.7.2.1 Current Rating.................................................................................................................................... 2-7
2.7.2.2 Connections ....................................................................................................................................... 2-7
2.7.3 D-C Output Grounding ............................................................................................................................ 2-8
2.7.4 Power Supply/Load Interface .................................................................................................................. 2-9
2.7.5 Load Connection - General ..................................................................................................................... 2-9
2.7.5.1 Local Sensing/Remote Sensing Select .............................................................................................. 2-9
2.7.6 Series Operation ..................................................................................................................................... 2-10
2.7.7 Parallel/redundant Operation .................................................................................................................. 2-10
2.7.7.1 Load Sharing...................................................................................................................................... 2-12
2.7.8 Master/Slave Configurations ................................................................................................................... 2-12
2.7.9 Analog I/O Connections .......................................................................................................................... 2-12
2.7.10 Internal Relay Configuration.................................................................................................................... 2-13
SECTION 3 - OPERATION
3.1 General ....................................................................................................................................................... 3-1
3.2 Local Mode Operation ................................................................................................................................ 3-1
3.2.1 Turning the Power Supply On ................................................................................................................. 3-1
3.2.2 Setting Local/Remote Mode .................................................................................................................... 3-2
3.2.2.1 Remote with Local (Front Panel) Lockout .......................................................................................... 3-3
3.2.3 Enabling/Disabling Output Power............................................................................................................ 3-3
3.2.4 Checking Voltage/Current Setpoints ....................................................................................................... 3-4
3.2.5 Defining a Virtual Model .......................................................................................................................... 3-4