KEPCO KLP Series (older -1200 models) Operator Manual - Manual (Page 9)

KLP SVC 020498
iii
TABLE OF CONTENTS
SECTION PAGE
3.6.4.5 Data Separator................................................................................................................................... 3-23
3.6.4.6 Message Unit Separator .................................................................................................................... 3-23
3.6.4.7 Root Specifier..................................................................................................................................... 3-23
3.6.4.8 Message Terminator .......................................................................................................................... 3-24
3.6.5 Understanding The Command Structure................................................................................................. 3-24
3.6.6 Program Message Syntax Summary....................................................................................................... 3-26
3.6.7 Status Reporting...................................................................................................................................... 3-26
3.6.7.1 Status Reporting Structure................................................................................................................. 3-26
3.6.7.2 Operational Status Register ............................................................................................................... 3-28
3.6.7.3 QUEStionable Status Register........................................................................................................... 3-28
3.6.8 SCPI Program Examples ........................................................................................................................ 3-28
3.7 Remote Programming Using Analog Signals ............................................................................................. 3-29
3.7.1 Enabling/Disabling the Output using Analog Control .............................................................................. 3-29
3.7.2 Programming with external resistance .................................................................................................... 3-30
3.7.3 Programming with external Voltage ........................................................................................................ 3-31
3.7.4 Changing Overvoltage or Overcurrent Protection Values in Analog Programming Mode....................... 3-31
SECTION 4 - CALIBRATION
4.1 General ....................................................................................................................................................... 4-1
4.2 Equipment Required ................................................................................................................................... 4-1
4.3 Calibration Using Front Panel Controls in Local Mode ............................................................................... 4-1
4.3.1 Voltage Calibration (Local) ...................................................................................................................... 4-2
4.3.2 Current Calibration (Local) ...................................................................................................................... 4-3
4.3.3 External Calibration (Local) ..................................................................................................................... 4-3
4.3.4 Calibration Exit (Local) ............................................................................................................................ 4-4
4.4 Calibration using VISA Driver Demo Program Soft Panel .......................................................................... 4-4
4.4.1 Voltage Calibration (VISA Demo)............................................................................................................ 4-5
4.4.2 Current Calibration (VISA Demo) ............................................................................................................ 4-6
4.4.3 Analog Reference Calibration (VISA Demo) ........................................................................................... 4-6
4.4.4 Calibration Exit (VISA Demo) .................................................................................................................. 4-7
4.5 Changing the Calibration Password ........................................................................................................... 4-7
4.6 Restoring Prior Calibration Values.............................................................................................................. 4-8
APPENDIX A - IEEE 488.2 COMMAND/QUERY DEFINITIONS
A.2 *CLS — Clear Status Command ............................................................................................................... A-1
A.3 *ESE — Standard Event Status Enable Command................................................................................... A-1
A.4 *ESE? — Standard Event Status Enable Query........................................................................................ A-2
A.5 *ESR? — Event Status Register Query..................................................................................................... A-2
A.6 *IDN? — Identification Query..................................................................................................................... A-2
A.7 *OPC — Operation Complete Command .................................................................................................. A-2
A.8 *OPC? — Operation Complete Query ....................................................................................................... A-3
A.9 *RCL — Recall Command ......................................................................................................................... A-4
A.10 *RST — Reset Command.......................................................................................................................... A-4
A.11 *SAV — Save Command........................................................................................................................... A-4
A.12 *SRE — Service Request Enable Command ............................................................................................ A-4
A.13 *SRE? — Service Request Enable Query ................................................................................................. A-5
A.14 *STB? — Status Byte Register Query ....................................................................................................... A-5
A.15 *TRG — Trigger Command ....................................................................................................................... A-5
A.16 *TST? — Self Test Query .......................................................................................................................... A-5
APPENDIX B - SCPI COMMAND/QUERY DEFINITIONS
B.1 Introduction ................................................................................................................................................ B-1
B.2 Numerical Values....................................................................................................................................... B-2
B.3 ABORt Command ...................................................................................................................................... B-2