KEPCO KLP Series (older -1200 models) Operator Manual - Manual (Page 103)

KLP 073008
B-17
= function enabled (active, true); bit reset to 0 = function disabled (inactive, false) . Related Com-
mands: STAT:QUES?. (See example, Figure B-6.)
B.66 SYSTem:COMMunication:GPIB:ADDRess COMMAND
SYST:COMM:GPIB:ADDR
Syntax: Short Form: SYST:COMM:GPIB:ADDR 01 to 30
Long Form: SYSTem:COMMunication:GPIB:ADDRess 01 to 30
Description: Sets selected power supply GPIB address. Two-digit address required
B.67 SYSTem:COMMunication:GPIB:ADDRess ? QUERY
SYST:COMM:GPIB:ADDR?
Syntax: Short Form: SYST:COMM:GPIB:ADDR?
Long Form: SYSTem:COMMunication:GPIB:ADDRess?
Return Value: GPIB address
Description: Returns GPIB address.
B.68 SYST em:COMMunication :SER ial: BAUD COMMAND
SYST:COMM:SER:BAUD
Syntax: Short Form: SYST:COMM:SER:BAUD {19200 | 9600 | 4800 | 2400}
Long Form: SYSTem:COMMunication:SERial:BAUD {19200 | 9600 | 4800 | 2400}
Description: Sets the unit to operate at the specified baud rate.
B.69 SYSTem:COMMunication :SER ial:BAUD? QUERY
SYST:COMM:SER:BAUD?
Syntax: Short Form: SYST:COMM:SER:BAUD?
Long Form: SYSTem:COMMunication:SERial:BAUD?
Return Value: {19200 | 9600 | 4800 | 2400}
B.70 SYST em :COMM unication :SER ial :ECHO COMMAND
SYST:COMM:SER:ECHO
Syntax: Short Form: SYST:COMM:SER:ECHO {1 | 0}
Long Form: SYSTem:COMMunication:SERial:ECHO {1 | 0}
Description: Enables (1 = ON) or disables (0 = OFF) echo mode (see PAR. 3.4.2.3). When echo mode is ON
causes all subsequent characters to be echoed back. When echo mode is OFF, turns off the character
echo after the nest line terminator character. The *RST command has no effect on echo status
B.71 SYST em :COMM unication :SER ial :ECHO? QUERY
SYST:COMM:SER:ECHO?
Syntax: Short Form: SYST:COMM:SER:ECHO?
Long Form: SYSTem:COMMunication:SERial:ECHO?
Return Value: (01
H
or 00
H
)
Description: Indicates whether echo mode is on (01
H
) or off (00
H
). (See PAR. 3.4.2.3.)
B.72 SYST em :COMM unication :SER ial :ENAB le COMMAND
SYST:COMM:SER:ENAB
Syntax: Short Form: SYST:COMM:SER:ENAB {1 | 0}
Long Form: SYSTem:COMMunication:SERial:ENAB {1 | 0}
Description: Enables (1 = ON) or disables (0 = OFF) transmission of data via the RS 232 port (see PAR. 3.4.2)
Once RS 232 transmission has been disabled, it can be enabled again by either turning the unit off,
then on, or by sending SYST:COMM:SER:ENAB 1 via the GPIB port.
B.73 SYST em :COMM unication :SER ial :ENAB? QUERY
SYST:COMM:SER:ENAB?
Syntax: Short Form: SYST:COMM:SER:ENAB?
Long Form: SYSTem:COMMunication:SERial:ENAB?
Return Value: (01
H
or 00
H
)
Description: Indicates whether RS 232 transmission mode is enabled (01
H
= ON) or disabled (00
H
= OFF).
(See PAR. 3.4.2.)
B.74 SYSTEM:COMMUNICATION:SERIAL:PACE COMMAND
SYST:COMM:SER:PACE
Syntax: Short Form: SYST:COMM:SER:PACE {NONE | XON}
Long Form: SYSTem:COMMunication:SERial:PACE {NONE | XON}