HEIDENHAIN SW 54843x-02 DIN Programming - Manual (Page 593)

HEIDENHAIN MANUALplus 620, CNC PILOT 640 593
G180 Starting point of contour in YZ
plane ... 487
G181 Line segment in YZ
plane ... 487
G182 Circular arc in YZ plane ... 488
G183 Circular arc in YZ plane ... 488
G2 circular arc in a contour ... 196
G20 Chuck part: bar/tube ... 192
G21 cast part ... 192, 369
G22 recess (standard) ... 198
G23 Recess (general) ... 200
G24 thread with undercut ... 202
G25 Undercut contour ... 203, 407
G3 circular arc in a turned
contour ... 196
G300 hole on front/rear face ... 224
G301 Linear slot on front/rear
face ... 225
G302 Circular slot on front/rear
face ... 225
G303 Circular slot on front/rear
face ... 225
G304 Full circle on front/rear
face ... 226
G305 Rectangle on front/rear
face ... 226
G307 Eccentric polygon on front/
rear face ... 227
G308 Beginning of pocket/
island ... 215
G309 End of pocket/island ... 215
G310 Hole on lateral surface ... 233
G311 Linear slot on lateral
surface ... 234
G312 Circular slot on lateral
surface ... 234
G313 Circular slot on lateral
surface ... 234
G314 Full circle on lateral
surface ... 235
G315 Rectangle, lateral
surface ... 235
G317 Eccentric polygon, lateral
surface ... 236
G34 Thread (standard) ... 207
G37 Thread (general) ... 208
G370 Hole in XY plane ... 480
G371 Linear slot in XY plane ... 481
G372 Circular slot in XY plane ... 482
G373 Circular slot in XY plane ... 482
G374 Full circle in XY plane ... 482
G375 Rectangle in XY plane ... 483
G376 Single surface in XY
plane ... 486
G377 Eccentric polygon in XY
plane ... 483
G38 Feed rate reduction ... 211, 212
G380 Hole in YZ plane ... 489
G381 Linear slot in YZ plane ... 489
G382 Circular slot in YZ plane ... 490
G383 Circular slot in YZ plane ... 490
G384 Full circle in YZ plane ... 490
G385 Rectangle in YZ plane ... 491
G386 Single surface in YZ
plane ... 494
G387, Eccentric polygon, YZ
plane ... 491
G401 Linear pattern on front/rear
face ... 228
G402 Circular pattern on front/rear
face ... 229
G411 Linear pattern on lateral
surface ... 237
G412 Circular pattern on lateral
surface ... 238
G471 Linear pattern in XY
plane ... 484
G472 Circular pattern in XY
plane ... 485
G477 Centric polygon in XY
plane ... 486
G481 Linear pattern in YZ
plane ... 492
G482 Circular pattern in YZ
plane ... 493
G487 Centric polygon in YZ
plane ... 494
G49 Hole (centric) ... 210
G52 Blockwise oversize ... 213
G95 Feed per revolution ... 214
G codes for machining
Contour repeat cycle G83 ... 411
G0 Rapid traverse ... 239
G0 Rapid traverse (Y axis) ... 497
G1 Linear movement ... 241
G1 Linear movement (Y axis) ... 499
G100 Rapid traverse on front/rear
face ... 329
G101 Linear segment on front/rear
face ... 330
G102 Circular arc on front/rear
face ... 331
G103 Circular arc on front/rear
face ... 331
G110 Rapid traverse, lateral
surface ... 333
G111 Line segment on lateral
surface ... 334
G112 Circular arc on lateral
surface ... 335
G113 Circular arc on lateral
surface ... 335
G12 Circular movement (Y
axis) ... 501
G12 Circular path ... 243
G120 Reference diameter ... 327
G13 Circular movement (Y
axis) ... 501
G13 Circular path ... 243
G14 Tool change point ... 240
G14 Tool change position (Y
axis) ... 497
G140 Definition of tool-change
point ... 240
G147 Safety clearance (milling
cycles) ... 255
G148 Cutter compensation,
switching ... 257
G149 Additive compensation ... 258
G150 Compensation of right-hand
tool tip ... 259
G151 Compensation of left-hand
tool tip ... 259
G152 Zero point shift, C axis ... 327
G153 Standardize C axis ... 328
G16 Tilting the working plane ... 496
G17 XY plane ... 495
G18 XZ plane (turning) ... 495
G19 YZ plane ... 495
G2 Circular movement (Y
axis) ... 500
G2 Circular path ... 242
G26 Speed limitation ... 244
G3 Circular movement (Y
axis) ... 500
G3 Circular path ... 242
G30 Converting and mirroring ... 376
G301 Linear slot on face ... 285
G302 Circular slot on face ... 285
G303 Circular slot on face ... 285
G304 Full circle on face ... 286
G305 Rectangle on face ... 286
G307 Eccentric polygon on front/
rear face ... 287
G31 Thread cycle ... 291
G311 Linear slot on lateral
surface ... 287