H3C Technologies H3C S7500E Series Switches - Manual (Page 125)

8-54
# Create VLAN 1 through VLAN 200.
system-view
[DeviceB] vlan 1 to 200
# Configure GigabitEthernet 2/0/1 and GigabitEthernet 2/0/2 as trunk ports and assign them to VLANs
1 through 200; enable flush message receiving on GigabitEthernet 2/0/1 and GigabitEthernet 2/0/2
and configure VLAN 10 and VLAN 101 as the receive control VLANs.
[DeviceB] interface gigabitethernet 2/0/1
[DeviceB-GigabitEthernet2/0/1] port link-type trunk
[DeviceB-GigabitEthernet2/0/1] port trunk permit vlan 1 to 200
[DeviceB-GigabitEthernet2/0/1] smart-link flush enable control-vlan 10 101
[DeviceB-GigabitEthernet2/0/1] quit
[DeviceB] interface gigabitethernet 2/0/2
[DeviceB-GigabitEthernet2/0/2] port link-type trunk
[DeviceB-GigabitEthernet2/0/2] port trunk permit vlan 1 to 200
[DeviceB-GigabitEthernet2/0/2] smart-link flush enable control-vlan 10 101
[DeviceB-GigabitEthernet2/0/2] quit
3) Configuration on Device D
# Create VLAN 1 through VLAN 200.
system-view
[DeviceD] vlan 1 to 200
# Configure GigabitEthernet 2/0/1 and GigabitEthernet 2/0/2 as trunk ports and assign them to VLANs
1 through 200; enable flush message receiving on GigabitEthernet 2/0/1 and GigabitEthernet 2/0/2
and configure VLAN 10 and VLAN 101 as the receive control VLANs.
[DeviceD] interface gigabitethernet 2/0/1
[DeviceD-GigabitEthernet2/0/1] port link-type trunk
[DeviceD-GigabitEthernet2/0/1] port trunk permit vlan 1 to 200
[DeviceD-GigabitEthernet2/0/1] smart-link flush enable control-vlan 10 101
[DeviceD-GigabitEthernet2/0/1] quit
[DeviceD] interface gigabitethernet 2/0/2
[DeviceD-GigabitEthernet2/0/2] port link-type trunk
[DeviceD-GigabitEthernet2/0/2] port trunk permit vlan 1 to 200
[DeviceD-GigabitEthernet2/0/2] smart-link flush enable control-vlan 10 101
[DeviceD-GigabitEthernet2/0/2] quit
4) Configuration on Device A
# Create VLAN 1 through VLAN 200.
system-view
[DeviceA] vlan 1 to 200
# Configure GigabitEthernet 2/0/1 and GigabitEthernet 2/0/2 as trunk ports and assign them to VLANs
1 through 200; enable flush message receiving on GigabitEthernet 2/0/1 and GigabitEthernet 2/0/2
and configure VLAN 10 and VLAN 101 as the receive control VLANs.
[DeviceA] interface gigabitethernet 2/0/1
[DeviceA-GigabitEthernet2/0/1] port link-type trunk
[DeviceA-GigabitEthernet2/0/1] port trunk permit vlan 1 to 200
[DeviceA-GigabitEthernet2/0/1] smart-link flush enable control-vlan 10 101
[DeviceA-GigabitEthernet2/0/1] quit
[DeviceA] interface gigabitethernet 2/0/2
[DeviceA-GigabitEthernet2/0/2] port link-type trunk
[DeviceA-GigabitEthernet2/0/2] port trunk permit vlan 1 to 200