H3C Technologies H3C S7500E Series Switches User Manual
Page 101
7-30
[DeviceA] rrpp domain 1
[DeviceA-rrpp-domain1] control-vlan 100
[DeviceA-rrpp-domain1] protected-vlan reference-instance 1
# Configure Device A as the master node of primary ring 1, with GigabitEthernet 2/0/1 as the
primary port and GigabitEthernet 2/0/2 as the secondary port, and enable ring 1.
[DeviceA-rrpp-domain1] ring 1 node-mode master primary-port gigabitethernet 2/0/1
secondary-port gigabitethernet 2/0/2 level 0
[DeviceA-rrpp-domain1] ring 1 enable
[DeviceA-rrpp-domain1] quit
# Create RRPP domain 2, configure VLAN 105 as the primary control VLAN of RRPP domain 2,
and configure the VLAN mapped to MSTI 2 as the protected VLAN of RRPP domain 2.
[DeviceA] rrpp domain 2
[DeviceA-rrpp-domain2] control-vlan 105
[DeviceA-rrpp-domain2] protected-vlan reference-instance 2
# Configure Device A as the master node of primary ring 1, with GigabitEthernet 2/0/2 as the
master port and GigabitEthernet 2/0/1 as the secondary port, and enable ring 1.
[DeviceA-rrpp-domain2] ring 1 node-mode master primary-port gigabitethernet 2/0/2
secondary-port gigabitethernet 2/0/1 level 0
[DeviceA-rrpp-domain2] ring 1 enable
[DeviceA-rrpp-domain2] quit
# Enable RRPP.
[DeviceA] rrpp enable
2) Configuration on Device B
# Create VLANs 1 and 2, map VLAN 1 to MSTI 1 and VLAN 2 to MSTI 2, and activate MST
region configuration.
[DeviceB] vlan 1 to 2
[DeviceB] stp region-configuration
[DeviceB-mst-region] instance 1 vlan 1
[DeviceB-mst-region] instance 2 vlan 2
[DeviceB-mst-region] active region-configuration
[DeviceB-mst-region] quit
# Set the physical state change suppression interval on GigabitEthernet2/0/1 and
GigabitEthernet2/0/2 to 0 seconds, disable STP, configure the two ports as trunk ports, and
assign them to VLAN 1 and VLAN 2.
[DeviceB] interface gigabitethernet 2/0/1
[DeviceB-GigabitEthernet2/0/1] link-delay 0
[DeviceB-GigabitEthernet2/0/1] undo stp enable
[DeviceB-GigabitEthernet2/0/1] port link-type trunk
[DeviceB-GigabitEthernet2/0/1] port trunk permit vlan 1 2
[DeviceB-GigabitEthernet2/0/1] quit
[DeviceB] interface gigabitethernet 2/0/2
[DeviceB-GigabitEthernet2/0/2] link-delay 0
[DeviceB-GigabitEthernet2/0/2] undo stp enable
[DeviceB-GigabitEthernet2/0/2] port link-type trunk
[DeviceB-GigabitEthernet2/0/2] port trunk permit vlan 1 2
[DeviceB-GigabitEthernet2/0/2] quit