Comtech EF Data KST-2000A/B - Manual (Page 124)

Ku-Band Satellite Transceiver Revision 9
Terminal Mode Commands MN/KST2000AB.IOM
B–14
B.3.6 Miscellaneous
Monitor and Control
Firmware Information Command
Response >add/MCFI_’cr’
VER_xxx.yyy.zzz’cr’
FW/nnnnn-ddr’cr’
mm/dd/yy’cr’’lf’] Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999)
nnnnn = Firmware number (0 to 99999)
dd = Firmware dash number (0 to 99)
r = Firmware revision (-, or A to Z)
Up Converter
Firmware Information Command
Response >add?UFI_’cr’
VER_xxx.yyy.zzz’cr’
FW/nnnnn-ddr’cr’
mm/dd/yy’cr’’lf’] Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999)
nnnnn = Firmware number (0 to 99999)
dd = Firmware dash number (0 to 99)
r = Firmware revision (-, or A to Z)
Down Converter
Firmware Information Command
Response
>add/DFI_’cr’
VER_xxx.yyy.zzz’cr’
FW/nnnnn-ddr’cr’
mm/dd/yy’cr’’lf’] Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999)
nnnnn = Firmware number (0 to 99999)
dd = Firmware dash number (0 to 99)
r = Firmware revision (–, or A to Z)
HPA Firmware
Information Command
Response >add/HFI_’cr’
VER_xxx.yyy.zzz’cr’
FW/nnnnn-ddr’cr’
mm/dd/yy’cr’’lf’] Where:
xxx.yyy.zzz = Software version number (0.0.0 to
999.999.999)
nnnnn = Firmware number (0 to 99999)
dd = Firmware dash number (0 to 99)
r = Firmware revision (–, or A to Z)
Query Serial
Numbers Status
Response
>add/SNUM_’cr’
UC_xxxxxxxxx’cr’
HPA_xxxxxxxxx’cr’
DC_xxxxxxxxx’cr’
M&C_xxxxxxxxx’cr’’lf’] Where:
xxxxxxxxx = Serial Number ( 0 to 999999999)
Query Assembly
Numbers Command
Response >add/ANUM_’cr’
UC_AS/nnnnn-ddr’cr’
HPA_AS/nnnnn-ddr’cr’
DC_AS/nnnnn-ddr’cr’
M&C_AS/nnnnn-ddr’cr’’lf’] Where: nnnnn = Assembly number (0 to 99999)
d = Dash number (0 to 9)
r = Revision (–, or A to Z)
TWTA Heater Command
Response
Status
Response >add/HTR_xxx’cr’’lf’]
>add/HTR_xxx’cr’’lf’] Where: xxx = WRM or HOT
Default = HOT
or N/A if TWTA is not HPA type
TWTA Fault Reset Command
Response >add/TWTR_RESET’cr’’lf’] Note: This clears out any existing faults for a connected
TWTA.
Equipment Type Command
Response >add/ET_ttttttttt_xxx.yyy.zzz’cr’’lf’]
Example: >1/ET_KST-2000A_1.1.1 Where: ttttttttt = Equipment Type
xxx.yyy.zzz = Software Version
HPA Connector
Location Command
Response >add?HCL2_xxx’cr’’lf’] Where: CEFD-SSPA
OEM-SSPA
OEM-TWTA
N/C (Not Connected)
This command returns the current location of the SSPA
M&C cable.