Interlogix Monitor XL Hardware Guide - Manual (Page 34)

30 Monitor ISM/xL™ Hardware Guide 22-0375 rev1.1
Smart/Vigil Concentrator to Smart/Vigil Module Inputs and Outputs Conversion Chart
Conc.
Input #
Module
Input #
Conc.
Input # Input #
Conc.
Output # Output #
Conc.
Output # Output #
1 9 C 33 41 1 11 C 41 51
O 2 10 O 34 42 O 2 12 O 42 52
N 3 11 N 35 43 N 3 13 N 43 53
C 4 12 C 36 44 C 4 14 C 44 54
5 13 37 45 5 15 45 55
# 6 14 # 38 46 # 6 16 # 46 56
1 7 15 5 39 47 1 7 17 5 47 57
8 16 40 48 8 18 48 58
9 17 C 41 49 9 9 49 49
O 10 18 O 42 50 10 10 50 50
N 11 19 N 43 51 C 11 21 C 51 61
C 12 20 C 44 52 O 12 22 O 52 62
13 21 45 53 N 13 23 N 53 63
# 14 22 # 46 54 C 14 24 C 54 64
2 15 23 6 47 55 15 25 55 65
16 24 48 56 # 16 26 # 56 66
17 25 C 49 57 2 17 27 6 57 67
O 18 26 O 50 58 18 28 58 68
N 19 27 N 51 59 19 19 59 59
C 20 28 C 52 60 20 20 60 60
21 29 53 61 C 21 31 C 61 71
# 22 30 # 54 62 O 22 32 O 62 72
3 23 31 7 55 63 N 23 33 N 63 73
24 32 56 64 C 24 34 C 64 74
C 25 33 C 57 65 25 35 65 75
O 26 34 O 58 66 # 26 36 # 66 76
N 27 35 N 59 67 3 27 37 7 67 77
C 28 36 C 60 68 28 38 68 78
29 37 61 69 29 29 69 69
# 30 38 # 62 70 30 30 70 70
4 31 39 8 63 71 C 31 41 C 71 81
32 40 64 72 O 32 42 O 72 82
N 33 43 N 73 83
C 34 44 C 74 84
35 45 75 85
# 36 46 # 76 86
4 37 47 8 77 87
38 48 78 88
39 39 79 79
40 40 80 80
C
C
C C
The first 8 inputs and outputs
of the ISM/AFx are located on
the main control board.
NOTE: This Table applies when the
Smart / Vigil Module is configured
as Module # 1.
Module Module Module
Smt/Vig Smt/Vig Smt/Vig Smt/Vig Smt/Vig Smt/Vig Smt/Vig Smt/Vig
Output Locations on Smart/Vigil Concentrators
Commercial Concentrator: output 9 becomes output 1. Output 10 becomes output 2. Outputs 1 – 8 on the plug on, 8-
zone annunciator card become outputs 3 – 10.
Safe/Vault Concentrator: outputs 1 – 5 start their programming at output 3 – 7.
Safe Seismic Concentrator: output 1 becomes output 3. Output 2 becomes output 4.
Checking Status
• When in the Status menu, select App and then SMA for the Smart/Vigil module.
• Select SMR to check Smart concentrators. HSC is NOT USED. Printer status and some printer user control is
in the History menu the same as using a Printer module (discussed later in this manual).