Canon SX 50 - Manual (Page 241)

Projector User Commands
- 235 -
Revision History / Date Changes Revised by Approved by
DG A1 A2 CM V SV DV SC X ON OFF
118 RANGE POWER
119 RANGE AUTOSETEXE
120 RANGE BLANK
121 RANGE INPUT
122 RANGE DOTS
← ←
123 RANGE TRACK ← ←
124 RANGE HPOS ← ←
125 RANGE VPOS ← ←
126 RANGE HPIX ← ←
127 RANGE VPIX ← ←
128 RANGE SEL ← ←
129 RANGE ASPECT
130 RANGE IMAGE
131 RANGE BRI
132 RANGE CONT
133 RANGE SHARP
134 RANGE GAMMA
135 RANGE DGAMMA
136 RANGE PROG
← ←
137 RANGE WB
138 RANGE WBRGB
139 RANGE SAT
－ －
－
141 RANGE RGBGAIN
142 RANGE RGBOFFSET
143 RANGE ACADJUST
- -
144 RANGE MEMCADJ
145 RANGE 6AXADJ
146 RANGE 6AXR～Y
147 RANGE VKS
← ←
148 RANGE HKS ← ←
149 RANGE AVOL
150 RANGE MUTE
151 RANGE BVOL
152 RANGE IMAGEFLIP
153 RANGE PMM
154 RANGE PJON
155 RANGE NOSIG
156 RANGE NOSHOW
157 RANGE LOGOPOS
158 RANGE LANG
159 RANGE LAMP
160 RANGE TERMINAL
- -
161 RANGE KEYLOCK
162 RANGE RCCH
163 RANGE DVRANGE
164 RANGE GUIDE
165 RANGE DPON
166 RANGE LEDILLUMINATE
167 RANGE ZSTEPDRV
168 RANGE ZCONTDRV
169 RANGE FSTEPDRV
170 RANGE FCONTDRV
Response Status Input signal
OK or Normal Response OFF Power Off DG Digital RGB V Video
BUSY OFF2ON Transitioning from power off→on A1 Analog RGB1 SV S-Video
INVALID_MODE ON Power ON A2 Analog RGB2 DV Digital Video
INVALID_SOURCE ON2OFF Transitioning from power on→off CM Component SC SCART
NOT_SUPPORTED_ASPECT ON2PMM Transitioning from power on→standby mode
NO_SIGNAL PMM Standby V Video X No signal
NOT_POWER_SUPPLIED PMM2ON Transitioning from standby→power on SV S-Video
BAD_SEQUENCE
NO_BLANK
INPUT_NOT_FOUND
No response
Version numbers of
models supported
ITEM Commands
Response
not send
LOCAL REMOTE
SX50
SX6
OFF OFF2ON
01.00**
PMM PMM2ON
SX60
X600 Input signal BLANK
01.01**
ON2PMM PMM PMM2ON ON2OFF ON2PMM OFF OFF2ON
ON
ON ON2OFF
○ ○
Ч ○
Ч ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
140 RANGE HUE ○ ○ ← ←
Ч ○
Ч ○
○ Ч
Ч ○
Ч ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ ○
○ Ч
○ ○
○ ○
Ч ○
Ч ○
Ч ○
Ч ○
Ч ○
Ч ○
Ч ○
Ч ○