Agilent Technologies B2201A User Manual
Agilent b2200a, Agilent b2201a
This manual is related to the following products:
Table of contents
Document Outline
- Agilent B2200 User’s Guide
- 1 Introduction
- 2 Installation
- 3 Front Panel Operation
- Operation
- To Initialize Agilent B2200
- To Enable Light Pen
- To Change Channel Configuration Mode
- To Change Connection Rule
- To Change Connection Sequence
- To Control Switch Condition
- To Open All Switches
- To Save/Load Setup Data
- To Use Bias Mode
- To Use Ground Mode
- To Use Couple Mode
- To Display Firmware Revision
- To Display Module Information
- To Read Error Message
- To Set Beeper
- To Set GPIB Address
- To Set Remote Display Mode
- To Return to Local Mode
- Switch Control Functions
- Display Functions
- Front Panel Keys
- Setup Menus
- Operation
- 4 Programming
- 5 SCPI Command Reference
- Common Commands
- Subsystem Commands
- Command Summary
- :DIAGnostic:TEST:CARD:CLEar
- :DIAGnostic:TEST:CARD[:EXECute]?
- :DIAGnostic:TEST:CARD:STATe?
- :DIAGnostic:TEST:FRAMe:CLEar
- :DIAGnostic:TEST:FRAMe[:EXECute]?
- :DIAGnostic:TEST:FRAMe:STATe?
- [:ROUTe]:AGND:CHANnel:DISable:CARD
- [:ROUTe]:AGND:CHANnel:DISable[:LIST]
- [:ROUTe]:AGND:CHANnel:ENABle:CARD
- [:ROUTe]:AGND:CHANnel:ENABle[:LIST]
- [:ROUTe]:AGND:PORT
- [:ROUTe]:AGND[:STATe]
- [:ROUTe]:AGND:UNUSED
- [:ROUTe]:BIAS:CHANnel:DISable:CARD
- [:ROUTe]:BIAS:CHANnel:DISable[:LIST]
- [:ROUTe]:BIAS:CHANnel:ENABle:CARD
- [:ROUTe]:BIAS:CHANnel:ENABle[:LIST]
- [:ROUTe]:BIAS:PORT
- [:ROUTe]:BIAS[:STATe]
- [:ROUTe]:CLOSe:CARD?
- [:ROUTe]:CLOSe[:LIST]
- [:ROUTe]:CONNection:RULE
- [:ROUTe]:CONNection:SEQuence
- [:ROUTe]:COUPle:PORT
- [:ROUTe]:COUPle:PORT:DETect
- [:ROUTe]:COUPle[:STATe]
- [:ROUTe]:FUNCtion
- [:ROUTe]:OPEN:CARD
- [:ROUTe]:OPEN[:LIST]
- [:ROUTe]:SYMBol:CHANnel
- [:ROUTe]:SYMBol:PORT
- :SYSTem:BEEP
- :SYSTem:CCONfig?
- :SYSTem:CDEScription?
- :SYSTem:CPON
- :SYSTem:CTYPe?
- :SYSTem:DISPlay:LCD
- :SYSTem:DISPlay:LED
- :SYSTem:DISPlay:STRing
- :SYSTem:ERRor?
- :SYSTem:KLC
- :SYSTem:MEMOry:COMMent
- :SYSTem:MEMOry:DELete
- :SYSTem:MEMOry:LOAD
- :SYSTem:MEMOry:SAVE
- :SYSTem:PEN
- :SYSTem:VERSion?
- Status Reporting Structure
- 6 VXI plug&play Driver
- System Requirements
- Installing VXIplug&play Driver
- Driver Functions
- agb220xa_biasChanCard
- agb220xa_biasChanList
- agb220xa_biasChanList_Q
- agb220xa_biasPort
- agb220xa_biasState
- agb220xa_close
- agb220xa_closeCard_Q
- agb220xa_closeList
- agb220xa_closeList_Q
- agb220xa_cmd
- agb220xa_cmdData_Q
- agb220xa_cmdInt
- agb220xa_cmdInt16Arr_Q
- agb220xa_cmdInt16_Q
- agb220xa_cmdInt32Arr_Q
- agb220xa_cmdInt32_Q
- agb220xa_cmdReal
- agb220xa_cmdReal64Arr_Q
- agb220xa_cmdReal64_Q
- agb220xa_cmdString_Q
- agb220xa_compenC
- agb220xa_connRuleSeq
- agb220xa_couplePort
- agb220xa_coupleState
- agb220xa_dcl
- agb220xa_detectCouplePort
- agb220xa_error_message
- agb220xa_error_query
- agb220xa_errorQueryDetect
- agb220xa_errorQueryDetect_Q
- agb220xa_esr_Q
- agb220xa_func
- agb220xa_groundChanCard
- agb220xa_groundChanList
- agb220xa_groundChanList_Q
- agb220xa_groundPort
- agb220xa_groundState
- agb220xa_init
- agb220xa_opc_Q
- agb220xa_openCard
- agb220xa_openList
- agb220xa_openList_Q
- agb220xa_readStatusByte_Q
- agb220xa_reset
- agb220xa_revision_query
- agb220xa_selectCompenFile
- agb220xa_self_test
- agb220xa_testClear
- agb220xa_testExec_Q
- agb220xa_timeOut
- agb220xa_timeOut_Q
- agb220xa_unusedPort
- 7 Error Messages