Yokogawa Button Operated MV2000 - Manual (Page 93)

4-19
Commands
IM MV1000-17E
1
2
3
4
5
6
7
App
Index
p2 Constant (–9.9999E+29 to –1.0000E–30,
0, 1.0000E–30 to 9.9999E+29, 5 significant
digits)
Query SK[ p1]?
Example Set constants number K01 to 1.0000E–10.
SKK01,1.0000E-10
Description • You can execute this command on models
with the /M1 math option.
• You cannot execute this command while the
MV is measuring or computing.
• Set parameter p1 according to the table in
section 4.3.
SI Sets rolling average on a
computation channel
Syntax SI p1,p2,p3,p4
p1 Computation channel number
p2 Moving average ON/OFF
p3 Sampling interval (1S, 2S, 3S, 4S, 5S, 6S,
10S, 12S, 15S, 20S, 30S, 1MIN, 2MIN,
3MIN, 4MIN, 5MIN, 6MIN, 10MIN, 12MIN,
15MIN, 20MIN, 30MIN, 1H)
p4 Number of samples (1 to 1500)
Query SI[ p1]?
Example Set the computation channel 107 rolling average
to ON, the sampling interval to 1 minute, and the
number of samples to 20.
SI107,ON,1MIN,20
Description • You can execute this command on models
with the /M1 math option.
• If p2 is set to OFF, do not specify p3 or p4.
• Set the sampling interval greater than or equal
to the scan interval.
SJ Sets a TLOG timer
Syntax SJ p1,p2,p3,p4,p5
p1 Computation channel number
p2 Timer (1 to 4)
p3 Conversion of the time unit for TLOG.SUM
computation
OFF
No conversion.
/S Convert as though the physical
values are integrated in units of
seconds.
/MIN Convert as though the physical
values are integrated in units of
minutes.
/H Convert as though the physical
values are integrated in units of
hours.
p4 Reset ON/OFF
p5 Timer type
TIMER
MATCHTIMETIMER
Query SJ[ p1]?
Example Set timer 1 to computation channel number 110.
Do not convert the unit time and enable the reset
function.
SJ110,1,OFF,ON
Description • You can execute this command on models
with the /M1 math option.
• Set parameter p1 according to the table in
section 4.3.
• You cannot execute this command while the
MV is computing.
• About p3
Because the sampled data is integrated
over each scan interval, the physical value
integrated over a given period may be different
from the actual integrated value. This occurs
if the given period is not equal to the scan
interval. In such case, set p3 to the same unit
as that of the physical value being measured.
The integrated value is found according to the
following converting equations that depend on
the parameter.
OFF
Σ (measured value)
/S Σ (measured value) × scan interval
/MIN Σ (measured value) × scan
interval/60
/HOUR Σ (measured value) × scan
interval/3600
The scan interval unit is seconds.
TX Sets the ancillary operation of
the start key
Syntax TX p1
p1 Computation operation (OFF, START,
RESET+START)
Query TX?
Example Configure the MV so that the start key also starts
computation.
TXSTART
FR Sets the FIFO buffer acquisition
interval
Syntax FR p1
p1 1 (fixed)
p1 FIFO acquisition interval (25MS, 125MS,
250MS, 500MS, 1S, 2S, 5S)
Query FR?
Example Set the FIFO acquisition interval to 1 s.
FR1,1S
Description • Set the acquisition interval to a value greater
than the scan interval.
• If you set the scan interval to a value greater
than the acquisition interval with the XV
command or from the screen, the acquisition
interval is automatically set equal to the scan
interval.
• The MV has a circular FIFO (First In First Out)
buffer. The MV acquires measured/computed
values to the internal memory at given time
4.4 Setting Commands (Setting)