beautypg.com

Run a menu (with no preheat feature), Parameter in the, Function of the configuration mode is set to – Watlow MINICHEF Deep Fat Fryer Application User Manual

Page 93: Ready, Setup, Idle, Alert

background image

A p p l i c a t i o n 1 8

Wa t l o w M i n i C h e f 2 0 0 0

9 1

acknowledge and silence the tone by pressing the Start/Stop key or it will automati-
cally time out within 2 seconds for setting 1 or 20 seconds for settings 2 or 3 and
then go into idle. The Start/Stop key indicator light will flash slowly. The controller
will maintain temperature at the programmed set point.

With sound set to 4 or 5: [``End] will appear on the display and the Start/Stop key
indicator light will flash rapidly. You must acknowledge the audible tone by pressing
the Start/Stop key. Once acknowledged the audible tone is silenced and the con-
troller goes into idle. The Start/Stop key indicator light will flash slowly. The con-
troller will maintain temperature at the programmed set point.

7.

Remove the food from the fryer.

8.

To repeat cooking, repeat steps 1 through 7.

Run a Menu (with no preheat feature)

This procedure describes how to run an active menu when the preheat feature is inac-
tive - in other words, when the

[ready]

parameter in the

[setUp]

function of the

Configuration Mode is set to

[```no]

.

1.

Select the menu you want to run as shown earlier in “Select a Menu”.

2.

With [idle`] or time of day on the display, place the food in the basket.

3.

Press the Start/Stop key.

The Start/Stop key indicator light will light up. Time will count down on the display.

4.

If programmed, as the time counts down, a mid-point alarm will appear on the dis-
play.

The alarm messages which varies based on programming will appear for ten sec-
onds.

An audible will sound for five seconds. Time will continue to count down on the dis-
play

5.

When the cooking cycle is finished one of the following will happen, depending on
the way the controller was programmed at [EtyPE] / [Sound]:

With Sound set to 0: The controller automatically switches to idle. [`idle] or cur-
rent time will appear on the display. The Start/Stop key indicator light will flash
slowly. The controller will maintain temperature at the programmed set point.

With Sound set to 1, 2, or 3: [``End] will appear on the display and an audible tone
will be emitted. The Start/Stop key indicator light will flash rapidly. You can
acknowledge and silence the tone by pressing the Start/Stop key or it will automati-
cally time out within 2 seconds for setting 1 or 20 seconds for settings 2 or 3 and
then go into idle. The Start/Stop key indicator light will flash slowly. The controller

D

E

C

F

M

INI

C

HEF

2000

[`idle]

Edit

Accept

Back-Up

Exit

D

E

C

F

M

INI

C

HEF

2000

[`0009]

Edit

Accept

Back-Up

Exit

B

D

E

C

F

M

INI

C

HEF

2000

[`idle]

Edit

Accept

Back-Up

Exit

G

H

A

A

B

G

H

A

B

G

H

D

E

C

F

M

INI

C

HEF

2000

[alert]

Edit

Accept

Back-Up

Exit

A

B

G

H

STEADY

ON

SLOW

FLASH

D

E

C

F

M

INI

C

HEF

2000

[``EnD]

Edit

Accept

Back-Up

Exit

B

D

E

C

F

M

INI

C

HEF

2000

[`idle]

Edit

Accept

Back-Up

Exit

G

H

A

A

B

G

H

RAPID FLASH

IF PROGRAMMED

SLOW FLASH