The melt cycle, Run a menu (with preheat feature), Parameter in the – Watlow MINICHEF Deep Fat Fryer Application User Manual
Page 43: Function of the configuration mode is set to, Ready, Setup, Idle, 100f, Pre-`] [`heat, I n i
A p p l i c a t i o n 1 3
Wa t l o w M
I N I
C
H E F
2 0 0 0
■
4 1
The heat output indicator light - G, just below the display- will light up whenever
the controller is calling for heat.
When the fryer is at operating temperature (above relative set point minus the
ready band) [ready] will appear on the display and the Start/Stop key indicator
light will flash rapidly. You are now ready to cook with the active menu.
If the fryer is at operating temperature, the display goes directly to [ready] with-
out indicating preheat or temperature.
The Melt Cycle
To avoid burning congealed oil (shortening), a slow heating action may be necessary. If
this is desired be sure that in the Configuration Mode [etype] / [melt]has been set
to [```on]. Then, when the oil temperature is below 212ºF the heat output will be lim-
ited to 10% of full power. This reduces the chance of burning congealed oil while it is
melting.
Run a Menu (with preheat feature)
This procedure describes how to run an active menu when the preheat feature is inac-
tive — in other words, when the
[ready]
parameter in the
[setUp]
function of the
Configuration Mode is set to
[``yes]
1. With
[`idle] on the display, press the key for the menu you want to run.
If the selected menu’s preheat condition has not been met, the fryer will preheat
until [ready] appears on the display. If the fryer is at operating temperature,
[ready] will immediately appear on the display.
2. With
[ready] on the display, place the food in the pressure fryer and secure the lid
on the pressure vessel.
3.
Press the active menu key (indicated by the rapidly flashing indicator light).
The menu key indicator light will light up. Time will count down on the display.
When the menu cycle nears completion, pressure will be released from the fryer
based on the time programmed in Configuration Mode, [etype] / [Ptine]
4. When the cooking cycle is finished, one of the following will happen, depending on
D
E
C
F
M
INI
C
HEF
2000
[ready]
Edit
Accept
Back-Up
Exit
D
E
C
F
M
INI
C
HEF
2000
[`0009]
Edit
Accept
Back-Up
Exit
B
D
E
C
F
M
INI
C
HEF
2000
[`idle]
Edit
Accept
Back-Up
Exit
G
H
A
A
B
G
H
A
B
G
H
STEADY
ON
SLOW
FLASH
D
E
C
F
M
INI
C
HEF
2000
[``EnD]
Edit
Accept
Back-Up
Exit
B
D
E
C
F
M
INI
C
HEF
2000
[`idle]
Edit
Accept
Back-Up
Exit
G
H
A
A
B
G
H
RAPID FLASH
SLOW FLASH
A
B
D
E
C
F
G
H
M
INI
C
HEF
2000
[idle`]
Edit
Accept
Back-Up
Exit
SLOW
FLASH
AT OPERATING TEMPERATURE
(PREHEAT CONDITION MET)
RAPID
FLASH
B
D
E
C
F
M
INI
C
HEF
2000
[100f`]
Edit
Accept
Back-Up
Exit
B
D
E
C
F
M
INI
C
HEF
2000
[ready]
Edit
Accept
Back-Up
Exit
G
H
G
H
A
A
[pre-`] [`Heat]