Extron Electronics SMD 101 User Guide - Manual (Page 70)

Symbol definitions
] = CR/LF (carriage return/line feed)
} or ¦ = Carriage return (no line feed, hex 0D)
• = Space
* = Asterisk character (which is a command
character, not a variable)
E or W = Escape
X! = Port number (two digits, zero padding)
X% = DHCP mode ( 0 =off, 1 =on)
X1! = Firmware version number
X1@ = Device name ( 63 characters, max)
Must comply with internet host name
standards. See RFC1123.
X1# = Day, date, and time (Day, DDMmmYYYY
HH:MM:SS)
X1$ = IP address in dotted decimal notation
(xxx.xxx.xxx.xxx)
Default:
192.168.254.254 no padding
X1% = Gateway address
Default: 0.0.0.0 no padding
X1* = Hardware MAC address
( 00‑05‑A6‑NN‑NN‑NN )
X1( = Subnet mask
default: 255.255.255.0 no padding)
X2@ = Verbose mode
0 =off/none (default for telnet connections
1 =verbose mode (default for RS-232 host
control)
2 =tagged responses for queries
3 =verbose mode and tagged responses
X2% = RS-232 baud rate (300 to 115200 bps,
default: 9600)
X2^ = RS-232 parity (default: none)
X2& = RS-232 data bits (default: 8 )
X2* = RS-232 stop bits (default: 1 )
X3# = Password: maximum length 12
characters. All alpha-numeric characters
permitted except
/ , \ , | ,"space", and " * ".
X3^ = HDMI output format:
0 =Auto (based on EDID), default
1 =DVI
2 =HDMI 444 RGB
(0-255, audio, InfoFrames)
3 =unused
4 =HDMI 444 YUV "Limited"
(16-235, audio, InfoFrames)
5 =unused
6 =HDMI 422 YUV "Limited"
(16-235, audio, InfoFrames)
X5) = RS-232 direct access mode
( 0 =disabled, 1 =host control, 2 =direct
access:pass-through)
X5@ = Security level:
11 =network user
12 =admin user
X6( = Port timeout in seconds (zero padded,
example 00050 )
X50! = Input number
1 or 2 digit command,
2 digit response (
00 =all)
X51) = 0 =Off/disable, 1 =On/enable)
X51@ = Internal temperature
(in degrees Celsius; xx.x)
X52! = Video Output Rate
10 = 640x480 @ 50 Hz
11 = 640x480 @ 60 Hz
12 = 800x600 @ 50 Hz
13 = 800x600 @ 60 Hz
14 = 1024x768 @ 50 Hz
15 = 1024x768 @ 60 Hz
16 = 1280x1024 @ 50 Hz
17 = 1280x1024 @ 60 Hz
18 = 1366x768 @ 50 Hz
19 = 1366x768 @ 60 Hz
20 = 1600x1200 @ 50 Hz
21 = 1600x1200 @ 60 Hz
22 = 1920x1200 @ 50 Hz
23 = 1920x1200 @ 60 Hz
24 = 480p @ 59.94 Hz
25 = 480p @ 60 Hz
26 = 576p @ 50 Hz
32 = 720p @ 50 Hz
33 = 720p @ 59.94 Hz
34 = 720p @ 60 Hz (default)
35 = 1080i @ 50 Hz
36 = 1080i @ 59.94 Hz
37 = 1080i @ 60 Hz
38 = 1080p @ 23.98 Hz
39 = 1080p @ 24 Hz
40 = 1080p @ 25 Hz
41 = 1080p @ 29.97 Hz
42 = 1080p @ 30 Hz
43 = 1080p @ 50 Hz
44 = 1080p @ 59.94 Hz
45 = 1080p @ 60 Hz
X52@ = Test Pattern
(two-digit response, 0 padding)
64 SMD 101 • Remote Communication and Control