ZyXEL Communications GS-2724 User Manual
Gs-2724, User’s guide
Table of contents
Document Outline
- User’s Guide
- Introduction and Hardware
- Basic Configuration
- Advanced
- VLAN
- Static MAC Forward Setup
- Filtering
- Spanning Tree Protocol
- 11.1 STP/RSTP Overview
- 11.1.1 STP Terminology
- 11.1.2 How STP Works
- 11.1.3 STP Port States
- 11.1.4 Multiple RSTP
- 11.2 Spanning Tree Protocol Main Screen
- 11.3 Configure Rapid Spanning Tree Protocol
- 11.4 Rapid Spanning Tree Protocol Status
- 11.5 Configure Multiple Rapid Spanning Tree Protocol
- 11.6 Multiple Rapid Spanning Tree Protocol Status
- Bandwidth Control
- Broadcast Storm Control
- Mirroring
- Link Aggregation
- Port Authentication
- Port Security
- Classifier
- Policy Rule
- Queuing Method
- VLAN Stacking
- Multicast
- 22.1 Multicast Overview
- 22.1.1 IP Multicast Addresses
- 22.1.2 IGMP Filtering
- 22.1.3 IGMP Snooping
- 22.2 Multicast Status
- 22.3 Multicast Setting
- 22.4 IGMP Filtering Profile
- 22.5 MVR Overview
- 22.5.1 Types of MVR Ports
- 22.5.2 MVR Modes
- 22.5.3 How MVR Works
- 22.6 General MVR Configuration
- 22.7 MVR Group Configuration
- 22.7.1 MVR Configuration Example
- IP Application
- Management
- Maintenance
- 28.1 The Maintenance Screen
- 28.2 Firmware Upgrade
- 28.3 Restore a Configuration File
- 28.4 Backup a Configuration File
- 28.5 Load Factory Default
- 28.6 Save Configuration
- 28.7 Reboot System
- 28.8 FTP Command Line
- 28.8.1 Filename Conventions
- 28.8.2 FTP Command Line Procedure
- 28.8.3 GUI-based FTP Clients
- 28.8.4 FTP Restrictions
- Access Control
- 29.1 Access Control Overview
- 29.2 The Access Control Main Screen
- 29.3 About SNMP
- 29.3.1 Supported MIBs
- 29.3.2 SNMP Traps
- 29.3.3 Configuring SNMP
- 29.4 SSH Overview
- 29.5 How SSH works
- 29.6 SSH Implementation on the Switch
- 29.6.1 Requirements for Using SSH
- 29.7 Introduction to HTTPS
- 29.8 HTTPS Example
- 29.8.1 Internet Explorer Warning Messages
- 29.8.2 Netscape Navigator Warning Messages
- 29.8.3 The Main Screen
- 29.9 Service Port Access Control
- 29.10 Remote Management
- Diagnostic
- Syslog
- Cluster Management
- MAC Table
- IP Table
- ARP Table
- Routing Table
- Configure Clone
- Maintenance
- CLI and Troubleshooting
- Introducing Commands
- 38.1 Overview
- 38.2 Accessing the CLI
- 38.2.1 The Console Port
- 38.3 The Login Screen
- 38.4 Command Syntax Conventions
- 38.5 Changing the Password
- 38.6 Privilege Levels
- 38.7 Command Modes
- 38.8 Getting Help
- 38.8.1 List of Available Commands
- 38.9 Using Command History
- 38.10 Saving Your Configuration
- 38.10.1 Configuration File
- 38.10.2 Logging Out
- 38.11 Command Summary
- 38.11.1 User Mode
- 38.11.2 Enable Mode
- 38.11.3 General Configuration Mode
- 38.11.4 interface port-channel Commands
- 38.11.5 interface route-domain Commands
- 38.11.6 config-vlan Commands
- 38.12 mvr Commands
- User and Enable Mode Commands
- 39.1 Overview
- 39.2 show Commands
- 39.2.1 show system-information
- 39.2.2 show ip
- 39.2.3 show logging
- 39.2.4 show interface
- 39.2.5 show mac address-table
- 39.3 ping
- 39.4 traceroute
- 39.5 Copy Port Attributes
- 39.6 Configuration File Maintenance
- 39.6.1 Using a Different Configuration File
- 39.6.2 Resetting to the Factory Default
- Configuration Mode Commands
- 40.1 Change the Out of Band Management IP Address
- 40.2 Enabling IGMP Snooping
- 40.3 Configure IGMP Filter
- 40.4 Enabling STP
- 40.5 no Command Examples
- 40.5.1 Disable Commands
- 40.5.2 Resetting Commands
- 40.5.3 Re-enable commands
- 40.5.4 Other Examples of no Commands
- 40.6 Static Route Commands
- 40.7 Enabling MAC Filtering
- 40.8 Enabling Trunking
- 40.9 Enabling Port Authentication
- 40.9.1 RADIUS Server Settings
- 40.9.2 Port Authentication Settings
- Interface Commands
- 41.1 Overview
- 41.2 Interface Command Examples
- 41.2.1 interface port-channel
- 41.2.2 bpdu-control
- 41.2.3 broadcast-limit
- 41.2.4 bandwidth-limit
- 41.2.5 mirror
- 41.2.6 gvrp
- 41.2.7 ingress-check
- 41.2.8 frame-type
- 41.2.9 weight
- 41.2.10 egress set
- 41.2.11 qos priority
- 41.2.12 name
- 41.2.13 speed-duplex
- 41.2.14 test
- 41.3 Interface no Command Examples
- 41.3.1 no bandwidth-limit
- IEEE 802.1Q Tagged VLAN Commands
- 42.1 Configuring Tagged VLAN
- 42.2 Global VLAN1Q Tagged VLAN Configuration Commands
- 42.2.1 GARP Status
- 42.2.2 GARP Timer
- 42.2.3 GVRP Timer
- 42.2.4 Enable GVRP
- 42.2.5 Disable GVRP
- 42.3 Port VLAN Commands
- 42.3.1 Set Port VID
- 42.3.2 Set Acceptable Frame Type
- 42.3.3 Enable or Disable Port GVRP
- 42.3.4 Modify Static VLAN
- 42.3.5 Delete VLAN ID
- 42.4 Enable VLAN
- 42.5 Disable VLAN
- 42.6 Show VLAN Setting
- Multicast VLAN Registration Commands
- Routing Domain Command Examples
- Troubleshooting
- Introducing Commands
- Appendices and Index