ZyXEL Communications ES-3148 Series User Manual
Es-3148 series, User’s guide
Table of contents
Document Outline
- User’s Guide
- Introduction
- Hardware
- Web Configurator
- The Web Configurator
- Initial Setup Example
- System Status and Port Statistics
- Basic Setting
- VLAN
- 8.1 Introduction to IEEE 802.1Q Tagged VLANs
- 8.1.1 Forwarding Tagged and Untagged Frames
- 8.2 Automatic VLAN Registration
- 8.2.1 GARP
- 8.2.2 GVRP
- 8.3 Port VLAN Trunking
- 8.4 Select the VLAN Type
- 8.5 Static VLAN
- 8.6 Subnet Based VLANs
- 8.7 Configuring Subnet Based VLAN
- 8.8 Protocol Based VLANs
- 8.9 Configuring Protocol Based VLAN
- 8.10 Create an IP-based VLAN Example
- 8.11 Port-based VLAN Setup
- 8.11.1 Configure a Port-based VLAN
- Static MAC Forward Setup
- Filtering
- Spanning Tree Protocol
- 11.1 STP/RSTP Overview
- 11.1.1 STP Terminology
- 11.1.2 How STP Works
- 11.1.3 STP Port States
- 11.1.4 Multiple RSTP
- 11.1.5 Multiple STP
- 11.2 Spanning Tree Protocol Status Screen
- 11.3 Spanning Tree Configuration
- 11.4 Configure Rapid Spanning Tree Protocol
- 11.5 Rapid Spanning Tree Protocol Status
- 11.6 Configure Multiple Rapid Spanning Tree Protocol
- 11.7 Multiple Rapid Spanning Tree Protocol Status
- 11.8 Configure Multiple Spanning Tree Protocol
- 11.9 Multiple Spanning Tree Protocol Status
- Bandwidth Control
- Broadcast Storm Control
- Mirroring
- Link Aggregation
- Port Authentication
- Port Security
- Classifier
- Policy Rule
- Queuing Method
- VLAN Stacking
- Multicast
- 22.1 Multicast Overview
- 22.1.1 IP Multicast Addresses
- 22.1.2 IGMP Filtering
- 22.1.3 IGMP Snooping
- 22.1.4 IGMP Snooping and VLANs
- 22.2 Multicast Status
- 22.3 Multicast Setting
- 22.4 IGMP Snooping VLAN
- 22.5 IGMP Filtering Profile
- 22.6 MVR Overview
- 22.6.1 Types of MVR Ports
- 22.6.2 MVR Modes
- 22.6.3 How MVR Works
- 22.7 General MVR Configuration
- 22.8 MVR Group Configuration
- 22.8.1 MVR Configuration Example
- Authentication & Accounting
- IP Source Guard
- Loop Guard
- Static Routing
- Differentiated Services
- DHCP
- Maintenance
- 29.1 The Maintenance Screen
- 29.2 Load Factory Default
- 29.3 Save Configuration
- 29.4 Reboot System
- 29.5 Firmware Upgrade
- 29.6 Restore a Configuration File
- 29.7 Backup a Configuration File
- 29.8 FTP Command Line
- 29.8.1 Filename Conventions
- 29.8.2 FTP Command Line Procedure
- 29.8.3 GUI-based FTP Clients
- 29.8.4 FTP Restrictions
- Access Control
- 30.1 Access Control Overview
- 30.2 The Access Control Main Screen
- 30.3 About SNMP
- 30.3.1 SNMP v3 and Security
- 30.3.2 Supported MIBs
- 30.3.3 SNMP Traps
- 30.3.4 Configuring SNMP
- 30.4 SSH Overview
- 30.5 How SSH works
- 30.6 SSH Implementation on the Switch
- 30.6.1 Requirements for Using SSH
- 30.7 Introduction to HTTPS
- 30.8 HTTPS Example
- 30.8.1 Internet Explorer Warning Messages
- 30.8.2 Netscape Navigator Warning Messages
- 30.8.3 The Main Screen
- 30.9 Service Port Access Control
- 30.10 Remote Management
- Diagnostic
- Syslog
- Cluster Management
- MAC Table
- ARP Table
- Configure Clone
- Troubleshooting and Specifications
- Appendices and Index