Toshiba Strata DK 16 - Manual (Page 90)

PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS
SECTION 100-816-302
MARCH 1993
2-66
NOTES:
1. For more information, see the instructions preceding the record sheets.
2. Initialized data reads LEDs 01, 05, 07, and 12 ON for all ports.
3. A range of ports may be specified by entering:
4. If this LED is turned OFF, OCA and Busy Override must be accessed manually by dialing 2. If kept ON, ACB and Executive Override
cannot be accessed.
5. If all stations are allowed Privacy Override, (the system will be non-private), allowing up to three telephones to talk on the same
CO line.
6. See Program 10-2 to enable/disable Priv./Exec./DND override warning tones.
7. To change DISA code from selected stations: Dial Intercom 6 5 8 + code + Redial.
8. DP or DTMF is specified for standard telephones only, KSTU, PSTU, or PESU (Circuits 1 and 2) in DK16, QSTU in DK8.
9. To change a four-digit Traveling Class Override (T.C.O.) code: Dial Intercom + ˚˚˚ + code + Redial.
˚˚˚ = 6 2 2 - Class 1, 6 2 3 - Class 2, 6 2 4 - Class 3, 6 2 5 - Class 4.
10. To change Verified Account Codes from selected stations: Dial Intercom + 6 5 9 + Code Number (000 ~ 299) for DK16; (000 ~ 099)
for DK8 + code (1 ~ 15 digits) + Redial. Note that the total Account Code digit length is set in Program 60-4; all digits do not have
to be verified.
11. To change the four-digit T. R. override codes (1 or 2) from selected stations: Dial Intercom + 6 5 4 + code + Redial; or Intercom
+ 6 5 5 + code + Redial.
12. Mic ON/OFF at start of call (LED 03 ON = Mic ON, LED 03 OFF = Mic OFF) is only in effect if Mic button lock is enabled (LED 02
= ON).
13. There are nine handset receiver volume levels, 1 ~ 9 (9 being the highest). The initial off-hook level can be set anywhere from level
2 to 5. Set the initial level with one of the following combinations: Level 2 = 12 OFF/13 OFF; Level 3 = 12 ON/13 OFF (default level);
Level 4 = 12 OFF/13 ON; Level 5 = 12 ON/13 ON.
14. To require DISA callers to dial Verified Forced Account Codes before accessing outside CO lines, light LEDs 08 and 14 on DK16
(Port 20) or DK8, (Port 10).
15. For ABR to function, QRCU (DK8) or K4RCU (DK16) must be installed to detect busy tone.
PROGRAM 30
STATION CLASS OF SERVICE
3 0 P S H H Z Z
Light LEDs for the port specified in the last step. All Button/
LEDs marked with an “X” in the table below should be lit.
Button/LEDs
SELECT = Logical Port Number(s)
S
Enter the logical port number(s) to which class of service
must be assigned. See Note 3 for entering a range of ports.
Feature LED
20
19
18
17
16
15
14
13
12
11
10
09
08
07
06
05
04
03
02
01
Logical Port Numbers and DISA Port 20
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19
Priv. Override Allowed
5,6
Exec. Override Allowed 6
DND Override Allowed
6
Change T.C.O. Code
9
Change Verified A.C. 10
Account Codes Verified
Digital Tele. Recv. Vol. 13
Digital Tele. Recv. Vol. 13
Dial Pulse/(DTMF Off)
8
Forced Acc't Code
OCA/Busy Override Automatic
4
ABR Access Enabled 15
Speed Dial Allowed
Mic on at Start of Call 12
Mic Button Lock Enabled
12
Speakerphone Enabled
Change DISA Security Code
7
Change TR Override Code 11
20
14
NOTE: Shaded areas apply to DK16 only
Low port High port