Toshiba Strata DK 16 User Manual

Page 77

PROGRAMMING PROCEDURES-INSTRUCTIONS/SYSTEM RECORDS

SECTION 100-816-302

MARCH 1993

2-53

PROGRAM 10-2

SYSTEM ASSIGNMENTS, PART 2 OF 3

SELECT = 2

Button/LEDs

Light LEDs as defined by the table below.
ALL LEDs with an "X" should be lit when you finish

4, 11

Button/LED

LED On

LED Off

–

Station External Amp Conference

Two CO Line Conference

“TRNS” Immediate (Soft Key)

Executive Override Warning Tone/ON

External Page included with All Call Page

Privacy Override Warning Tone/ON

Send Auto Callback Camp-on Tone

CO Line 3 min Beep Tone

No DTMF Tone Return

BGM connected to QSTU (DK8), PORT 19;

BGM connected to PEKU, Circuit 3

9,10

Display Dialed Number/1min.

–

No External Amplifier Connected

No Two CO Line Conference

“TRNS” Normal (Soft Key)

Executive Override Warning Tone/OFF

Not Included

Privacy Override Warning Tone/OFF

No Callback Tone

No Beep Tone

DTMF Tone Return

Telephone connected to CKT

Display Dialed Number/15 sec.

Standard Tel., CO Ring
per Prog. 10-1, LED 06

VM ID Code DTMF Signal Time 80 ms

DISA Busy Tone, 0.5 second cadence

MW cancel from VM; dial

6 4

& Station No.

Ringing Modes/3

Hunt/C.F. override from DSS console's phone

Tone First (from DSS Console)

Standard Tel. CO Ring Distinctive

160 ms

DISA Busy Tone, 0.25 second cadence

MW cancel from VM: Automatic

Ringing Modes/2

Hunt/C.F. override from DSS console

Voice First (from DSS Console)

NOTE: Shaded areas apply to DK16 only

PESU (DK16), Circuit 8

9,10

NOTES:

1. For more information, see the instructions preceding the record sheets.
2. Initialized data lights LEDs 02, 14, 15 and 16.
3. Called party receives notification tone when calling party activates Automatic Callback.
4. BGM connected to QSTU/PSTU/PEKU/PESU/KSTU, will be sent to electronic and digital telephone speakers and external page

(optional). Important: Power must be turned off and on for BGM assignments to be effective.

5. Ring pattern for standard telephones: distinctive ring on incoming CO calls, is: 0.2 sec. on, 0.4 sec. off, 0.2 sec. on, 3.4 sec. off; intercom

ring is always 1 sec. on, 3 sec. off. This doesn't apply to voice mail ports (Program 31, LED 17 on) which are always standard ring.

6. External speakers and designated digital and electronic telephones are paged by dialing

Intercom 3 9

. The

All Call Page

button is

used only to page designated digital and electronic telephones.

7. Deletes DTMF tones returned to digital and electronic telephones when dialing from dialpad or speed dialing; also deletes auto dial digits

sent to callers that are call forwarded to voice mail. This does not affect the actual DTMF tones sent out to the CO or voice mail.

8. 0.5 second cadence, Bell Standard Busy Tone, should be enabled so outside callers are not confused by STRATA 0.25 second busy

tone when calling busy number on DISA line calls.

9. If BGM source is assigned to KSTU or PSTU slot in Program 19, system automatically assigns KSTU or PSTU CKT 4 as a BGM source.

10. Important: LED 19 should be OFF unless external amplifiers are used for two CO line/station conference (see Program 10-3). If LED 19

is ON, the station may be unbalanced and receive HUM if external amplifier with Auto-Gain-Control is not connected.

11. BGM connected to QSTU, circuit 2, (DK8) Port 19 may require an isolation transformer per Section 100-816-207