SATO HT200e - Manual (Page 98)

SECTION 5 ： PRESET, TABLE DATA
Page 5-6 SATO HT200e
DELETION OF PRESET DATA
[RCL]
[ → ]
[ → ]
[ → ]
[ENTR]
[ENTR]
[ENTR]
Note: Where asterisk mark or “*” can be seen in the upper right on the screen, entry by scanner can be made
possible.
Ｆ Ｏ Ｒ Ｍ Ａ Ｔ Ｎ ｏ
1 ［ ・ ・ ］
Ｈ Ｔ ２ ０ ０ ｅ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
2 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
3 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
4 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
5 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｎ Ｏ ． Ｉ Ｎ Ｐ Ｕ Ｔ ＊
6 ・ ・ ・ ・ ＜ Ｄ Ｅ Ｌ Ｅ Ｔ Ｅ ＞
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｄ Ｅ Ｌ Ｅ Ｔ Ｅ Ｏ Ｋ
7 ・ ・ － ・ ・ ・ ・ Ｙ ／ Ｎ
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｄ Ｅ Ｌ Ｅ Ｔ Ｅ Ｄ
8
The screen for the selection of preset printing will
be displayed: Press [
→ ], so that it goes to the
screen for the process No. 3.
Press [RCL], so that it goes from the modes of
the print to the preset.
The screen for the selection of preset deletion will
be displayed: Press [ENTR], so that it goes to the
entry of preset number.
The screen for the selection of preset storing will
be displayed: Press [
→ ], so that it goes to the
screen for the process No. 4.
The screen for the selection of preset modification
will be displayed: Press [
→], so that it goes to the
screen for the process No. 5.
The preset No. that is required to delete can be
entered: Press [ENTR], so that it appears the con-
firmation for deletion.
Use [ ← ] and [ → ] to respond to the confirmation.
Press [ENTR], so that it deletes the preset data
specified.
When specified preset is deleted, it will display a
message for the end of deletion and returns to the
process No. 6.