SATO HT200e - Manual (Page 97)

SECTION 5 ： PRESET, TABLE DATA
SATO HT200e Page 5-5
MODIFICATION OF PRESET DATA
[RCL]
[ → ]
[ → ]
[ENTR]
[ENTR]
[ENTR]
[ENTR]
Note: Where asterisk mark or “*” can be seen in the upper right on the screen, entry by scanner can be made
possible.
Ｆ Ｏ Ｒ Ｍ Ａ Ｔ Ｎ ｏ
1 ［ ・ ・ ］
Ｈ Ｔ ２ ０ ０ ｅ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
2 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
3 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
［ Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ ］
4 Ｐ Ｒ Ｉ Ｎ Ｔ Ｓ Ｔ Ｒ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ
Ｄ Ｅ Ｌ Ｄ Ｕ Ｍ Ｐ Ｍ Ａ Ｓ Ｔ Ｅ Ｒ
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｎ Ｏ ． Ｉ Ｎ Ｐ Ｕ Ｔ ＊
5 ・ ・ ・ ・ ＜ Ｍ Ｏ Ｄ Ｉ Ｆ Ｙ ＞
［ Ｉ Ｔ Ｅ Ｍ ］
6 ・ ・ ・ ・ ・ ・ ・ ・ ・
［ Ｐ Ｒ Ｉ Ｃ Ｅ ］
7 ￡ ・ ・ ・ ・ ・ ・
The screen for the selection of preset printing will
be displayed: Press [
→ ], so that it goes to the
screen for the process No. 3.
Press [RCL], so that it goes from the modes of the
print to the preset.
The screen for the selection of preset storing will be
displayed: Press [
→ ], so that it goes to the screen
for the process No. 4.
The screen for the selection of preset modification
will be displayed: Press [ENTR], so that it goes to
the entry of preset number.
The preset No. that is required to print can be
entered: Press [ENTR], so that it displays the pre-
set data specified.
Since the contents for data will be changed,
based on the format No. retrieved, enter data
required to modify for each field, and press
[ENTR].
Note: Entry by scanner is available when ITEM
is input.
In the last field, press [ENTR] so that data will
be replaced.