SATO HT200e - Manual (Page 39)

SECTION 2: INSTALLATION AND SETUP
SATO HT200e Page 2-21
PROCESS ON THE SCREEN FOR DATA MAINTENANCE MODE
1. Copy for print parameter (From a card to a printer, or opposite direction)
2. Transfer for print parameter (From a card to a printer, or opposite direction)
3. Transfer for preset data (From a card to a printer, or opposite direction)
4. Transfer for font (From a card to a printer, or opposite direction)
5. Transfer for table data (From a card to a printer, or opposite direction)
6. Setting for currency mark
7. Card clear
8. Code setting for EAN country
6 + Power “ON”
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
[ ← ] [ → ]
Ｐ Ａ Ｒ Ａ Ｍ Ｅ Ｔ Ｅ Ｒ Ｃ Ｏ Ｐ Ｙ
1 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｃ Ａ Ｒ Ｄ
Ｄ Ａ Ｔ Ａ Ｓ Ｔ Ｏ Ｒ Ｅ ／ Ｒ Ｃ Ａ Ｌ Ｌ
2 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｐ Ｒ Ｅ Ｓ Ｅ Ｔ Ｓ Ｔ Ｒ ／ Ｒ Ｃ Ａ Ｌ Ｌ
3 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｆ Ｏ Ｎ Ｔ Ｓ Ｔ Ｏ Ｒ Ｅ ／ Ｒ Ｃ Ａ Ｌ Ｌ
4 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｔ Ａ Ｂ Ｌ Ｅ Ｓ Ｔ Ｒ ／ Ｒ Ｃ Ａ Ｌ Ｌ
5 Ｐ Ｒ Ｉ Ｎ Ｔ Ｅ Ｒ ← → Ｈ Ｏ Ｓ Ｔ
Ｃ Ｕ Ｒ Ｒ Ｅ Ｎ Ｃ Ｙ Ｓ Ｅ Ｌ Ｅ Ｃ Ｔ
6
Ｃ Ａ Ｒ Ｄ Ｃ Ｌ Ｅ Ａ Ｒ
7
Ｅ Ａ Ｎ Ｃ Ｏ Ｕ Ｎ Ｔ Ｒ Ｙ Ｃ Ｏ Ｄ Ｅ
8 ５ ０
Press [ENTR], so that it goes to the screen for the
copy of print parameter. Use [
→ ] to move to the
process No. 2.
Press [ENTR], so that it goes to the screen for the
transfer of print parameter.
Press [
← ] to go to the process No. 1.
Press [ → ] to go to the process No. 3.
Press [ENTR], so that it goes to the screen for the
transfer of preset data.
Press [
← ] to go to the process No. 2.
Press [ENTR], so that it goes to the screen for the
transfer of table data.
Press [
← ]to go to the process No. 4.
Press [ENTR], so that it goes to the screen for the
font transfer.
Press [
← ] to go to the process No. 3.
Press [ → ] to go to the process No. 5.
Press [ENTR], so that it goes to the screen for the
selection of currency mark.
Press[
← ] to go to the process No. 5.
Press [ENTR], so that it goes to the screen for the
code setting of EAN country. Select value from 00 t
99. Note that default value id 50.
Press [
← ]to go to the process No. 7.
Press [ENTR], so that it goes to the screen for the
confirmation of card clear.
Press [
← ] to go to the process No. 6.