beautypg.com

Custom panel dimensions – GE Monogram ZISB42D User Manual

Page 13

background image

13

Custom Panel Dimensions

42" Built-In Refrigerator

Custom Door Panel Dimensions

Using Trim Kit ZKT42

3/4" thick panel with custom handle

and/or ZWCD1 custom collar trim

Detail B

Rout panels to specification below on

the handle side of each panel

Important: Maintain 1-1/2" min. gap between
top of doors and bottom of grille panel.

Grille Panel height can vary to fill installation
height.

Installation Height

Dimension A

83"

8-1/4"

83-1/2"

8-3/4"

84"

9-1/4"

84-1/2"

9-3/4"

ZISW42D (white dispenser)
ZISB42D (black dispenser)

• ZKT42 and ZKHT1 installed together provides for the

installation of 3/4" custom door and grille panels, using
a custom handle of your choice. Cut panels to size, rout
the handle side of the panels as shown below and install
(see detail B).

• For ZKHTSS1 tubular stainless steel handle kit, cut panels

to size and rout the handle side of the panels as shown in
detail B.

• For standard dispenser trim: Cut panels to size, rout the

handle side of the panels as shown in detail B, rout the
bottom of the upper freezer panel and the top of the lower
freezer panel to allow placement of support brackets (see
detail A) and install.

• For custom dispenser trim ZWCD1 kit must be used: Cut

panels to size, refer to detail C for dispenser cutout
routing instructions. When a raised panel design is used,
a custom middle rail is required. A 14-1/2" wide middle rail
must be used because the custom collar trim must be
located within the raised portion of the panel. This area
must be 3/4" thick. See detail D for raised panel design
requirements.

• When using the standard full-width dispenser trim, the

length of the custom handle, top to bottom cannot exceed
11-3/4". Locate the handle a minimum of 3/4" and a
maximum of 1-1/2" from the edge of the panel. There are
no length restrictions on handles for models using a
custom collar dispenser trim (ZWCD1).

1 13/16"

1 13/16"

1/4"

max

Freezer Door Face

Freezer Door Face

Fresh Food Door Face

Detail A

Upper

Freezer

Panel

Lower

Freezer

Panel

Panel

Face

1"

1"

3/32"

CUSTOM PANEL

DIMENSIONS

9 7/16"

12 5/16"

7/8"
Wide
Rout

The Cutout is 9 7/16" wide
by 12 5/16" high. 3/4" panels
must be routed on all four
sides of the cutout. Rout
the back side of the panel
1/4" deep. 7/8" wide
(shaded area).

Detail C Custom

Dispenser Cutout

16 11/16"

37"

2 9/16"

67 15/16"

25 5/16"

17 11/16"

Fresh Food

Panel

Freezer Panel

Standard

Dispenser

Freezer Panel

Custom

Dispenser

15 5/16"

15 5/16"

Custom Grille Panel

41 1/2"

A

Over 1/4" Thick (3/4" max) Panel

Hole is Cut
After Door
Fabrication

14 1/2"

Wide

Middle

Rail

Detail D

Raised Panel Design

Handle
Side

A

A

Section AA

*Custom Stiles and

Middle Rail Required

*3" Stiles
Left Side

*2-3/16" Stiles
Right Side

Important: Maximum weight for fresh food panels is
50 pounds and 30 pounds for freezer door panels.

This manual is related to the following products: