FUJITSU PRIMERGY RX900 S1 User Manual
Primergy rx900 s1 server
Table of contents
Document Outline
- Contents
- Introduction
- Before you start
- Safety instructions
- Basic procedures
- Power supply
- Installing a hot-plug Power Supply Unit (PSU)
- Replacing a hot-plug power supply unit
- Removing a redundant hot-plug power supply unit
- Replacing the power distribution board
- Required tools
- Starting the task
- Sliding the local service display outward
- Disconnecting the cables
- Removing the fan cage
- Removing the CPUMEMR guide
- Removing the air guide
- Removing the baseboard
- Removing the power distribution board
- Installing the power distribution board
- Inserting the baseboard
- Installing the air guide
- Inserting the CPUMEMR guide
- Inserting the fan cage
- Connecting the cables to the baseboard
- Sliding the local service display inward
- Completing the task
- Hard disk and solid state drives
- Installing the HDD/SSD module
- Replacing the HDD/SSD module
- Removing the HDD/SSD module
- Replacing the SAS backplane
- Required tools
- Starting the task
- Sliding the local service display outward
- Disconnecting the cables
- Sliding the optical drive outward
- Removing the air guide
- Removing the SAS backplane
- Installing the SAS backplane
- Installing the air guide
- Sliding the optical drive inward
- Connecting the cables to the baseboard
- Sliding the local service display inward
- Completing the task
- Fan modules
- Expansion cards and BBU
- Mounting expansion card slot brackets
- Installing SFP+ transceiver modules
- Replacing SFP+ transceiver modules
- Installing a hot-plug expansion card
- Removing a hot-plug expansion card
- Replacing a hot-plug expansion card
- Required tools
- Starting the task
- Deactivating the expansion card
- Pulling the expansion card out of the slot
- Removing the expansion card from the removal tool
- Removing the engaging hooks
- Inserting an expansion card in the removal tool
- Inserting the expansion card in the slot
- Activating the expansion card
- Completing the task
- Installing a non-hot-plug expansion card
- Removing a non-hot-plug expansion card
- Replacing a non-hot-plug expansion card
- Replacing the Modular RAID controller
- Installing a Battery Backup Unit (BBU)
- Replacing a Battery Backup Unit (BBU)
- Main memory
- Processors
- Optical and backup drives
- Front panel and external connectors
- Management and diagnostics modules
- Baseboard
- Replacing the lithium battery
- Installing the UFM
- Replacing the UFM board
- Installing the TPM
- Replacing the TPM
- Replacing the baseboard
- Required tools
- Starting the task
- Sliding the local service display outward
- Disconnecting the cables
- Removing the fan cage
- Removing the CPUMEMR guide
- Removing the air guide
- Removing the baseboard
- Inserting the baseboard
- Installing the air guide
- Inserting the CPUMEMR guide
- Inserting the fan cage
- Connecting the cables to the baseboard
- Sliding the local service display inward
- Completing the task
- Cables
- Replacing the fan cables
- Replacing the control panel cable
- Replacing the chassis ID board cable
- Replacing power cables of the optical drive, the SAS backplane, or the power distribution board
- Required tools
- Starting the task
- Sliding the local service display outward
- Disconnecting the cables
- Removing the fan cage
- Removing the CPUMEMR guide
- Removing the air guide
- Removing the baseboard
- Removing the power distribution board
- Disconnecting the defective power distribution cable(s)
- Connecting the new power distribution cable(s)
- Installing the power distribution board
- Inserting the baseboard
- Installing the air guide
- Inserting the CPUMEMR guide
- Inserting the fan cage
- Connecting the cables to the baseboard
- Sliding the local service display inward
- Completing the task
- Replacing the SAS cable, the SATA cable, the front video connector cable, or the front USB cable
- Required tools
- Starting the task
- Sliding the local service display outward
- Disconnecting the cables
- Removing the fan cage
- Removing the CPUMEMR guide
- Removing the air guide
- Removing the baseboard
- Opening the cable guides
- Closing the cable guides
- Inserting the baseboard
- Installing the air guide
- Inserting the CPUMEMR guide
- Inserting the fan cage
- Connecting the cables to the baseboard
- Sliding the local service display inward
- Completing the task
- Appendix