FUJITSU SPARC ENTERPRISE M3000 User Manual

FUJITSU Computers

Table of contents

Document Outline

Contents
Preface
Safety Precautions for Maintenance
- 1.1 ESD Precautions
- 1.2 Server Precautions
Hardware Overview
- 2.1 Name of Each Part
- 2.2 Operator Panel
- 2.3 LED Functions of Components
- 2.4 External Interface Port on Rear Panel
- 2.5 Labels
Troubleshooting
- 3.1 Emergency Power Off
- 3.2 Failure Diagnostic Method
- 3.3 Checking the Server and System Configuration
  - 3.3.1 Checking the Hardware Configuration and FRU Status
    - 3.3.1.1 Checking the Hardware Configuration.
  - 3.3.2 Checking the Software and Firmware Configurations
- 3.4 Error Conditions
- 3.5 Using Troubleshooting Commands
- 3.6 General Solaris Troubleshooting Commands
FRU Replacement Preparation
- 4.1 Tools Required for Maintenance
- 4.2 FRU Replacement and Installation Methods
  - 4.2.1 FRU Replacement
  - 4.2.2 FRU Installation
- 4.3 Active Replacement/Active Addition
- 4.4 Hot Replacement/Hot Addition
  - 4.4.1 FRU Removal and Replacement
  - 4.4.2 Verifying the Hardware Operation
- 4.5 Cold Replacement/Cold Addition
Internal Components Access
- 5.1 Sliding the Server Into and Out of the Equipment Rack
  - 5.1.1 Sliding the Server Out from the Equipment Rack
  - 5.1.2 Sliding the Server into the Equipment Rack
- 5.2 Removing and Attaching the Top Cover
  - 5.2.1 Removing the Top Cover
  - 5.2.2 Attaching the Top Cover
- 5.3 Removing and Attaching the Air Duct
- 5.4 Removing and Attaching the Fan Cover
  - 5.4.1 Removing the Fan Cover
  - 5.4.2 Attaching the Fan Cover
Motherboard Unit Replacement
- 6.1 Accessing the Motherboard Unit
- 6.2 Removing the Motherboard Unit
- 6.3 Mounting the Motherboard Unit
- 6.4 Reassembling the Server
Replacement and Installation of Memory
- 7.1 Memory Mounting Rules
  - 7.1.1 Confirmation of DIMM Information
  - 7.1.2 Memory Mounting Conditions
- 7.2 Accessing the DIMMs
- 7.3 Removing the DIMMs
- 7.4 Installing the DIMMs
- 7.5 Reassembling the Server
Replacement and Installation of PCIe Cards
- 8.1 Accessing a PCIe Card
- 8.2 Removing a PCIe Card
- 8.3 Mounting a PCIe Card
- 8.4 Reassembling the Server
Replacement and Installation of a Hard Disk Drive (HDD)
- 9.1 Accessing a Hard Disk Drive
- 9.2 Removing a Hard Disk Drive
- 9.3 Installing a Hard Disk Drive
- 9.4 Reassembling the Server
Replacing the Hard Disk Drive Backplane
- 10.1 Accessing the Hard Disk Drive Backplane
- 10.2 Removing the Hard Disk Drive Backplane
- 10.3 Mounting the Hard Disk Drive Backplane
- 10.4 Reassembling the Server
CD-RW/DVD-RW Drive Unit (DVDU) Replacement
- 11.1 Accessing the CD-RW/DVD-RW Drive Unit
- 11.2 Removing the CD-RW/DVD-RW Drive Unit
- 11.3 Mounting the CD-RW/DVD-RW Drive Unit
- 11.4 Reassembling the Server
Power Supply Unit Replacement
- 12.1 Accessing a Power Supply Unit
- 12.2 Removing the Power Supply Unit
- 12.3 Mounting the Power Supply Unit
- 12.4 Reassembling the Server
Fan Unit Replacement
- 13.1 Accessing a Fan Unit
- 13.2 Removing a Fan Unit
- 13.3 Mounting a Fan Unit
- 13.4 Reassembling the Server
Fan Backplane Replacement
- 14.1 Accessing the Fan Backplane
- 14.2 Removing the Fan Backplane
- 14.3 Mounting the Fan Backplane
- 14.4 Reassembling the Server
Operator Panel Replacement
- 15.1 Accessing the Operator Panel
- 15.2 Removing the Operator Panel
- 15.3 Mounting the Operator Panel
- 15.4 Reassembling the Server
Components List
FRU List
- B.1 Server Overview
- B.2 Motherboard Unit
- B.3 Drive
  - B.3.1 Hard Disk Drive
  - B.3.2 CD-RW/DVD-RW Drive Unit (DVDU)
- B.4 Power Supply Unit
- B.5 Fan Unit
External Interface Specifications
- C.1 Serial Port
- C.2 UPC Port
- C.3 USB Port
- C.4 SAS Port
- C.5 Connection Diagram for Serial Cable
UPS Controller
- D.1 Overview
- D.2 Signal Cable
- D.3 Configuration of Signal Lines
- D.4 Power Supply Conditions
  - D.4.1 Input Circuit
  - D.4.2 Output Circuit
- D.5 UPS Cable
- D.6 Connections
DC Power Supply Model
- E.1 The Server Views
- E.2 LED Functions of Power Supply Unit
- E.3 Electricals Specifications
- E.4 Using the showhardconf Command
Abbreviations
Index