Emulex DCP_link Instruction Manuals and User Guides
We have 1 Instruction Manual and User Guide for DCP_link Emulex
Manuals 
| Recognized languages: | English |
|---|---|
| Pages: | 136 |
| Size: | 1.21 MB |
Show table of contents
Document Outline
- WANFRONT.DOC
- WAN_TOFC.DOC
- WAN_INTR.DOC
- WANINST1.DOC
- WANINST2.DOC
- WANINST3.DOC
- WANINST4.DOC
- Chapter 4
- Software Installation Procedure
- Installing to Novell NetWare version 3.12
- 1) At the NetWare server system console prompt, type
- 2) Select Product Options and press
. - 3) Press to begin the installation.
- 4) Insert the DCP_link INSTALL diskette into a floppy disk drive and enter the drive’s letter; simply press
to accept the default drive A: - 5) When the source files have been copied, the following message is displayed:
- 6) Press
. The Installation Options menu will again be displayed. - 7) Select Display Log File after install to check for any installation problems. A list of files that were not installed (for any reason) will be displayed at the bottom of the Display Log File.
- 8) Select Display README Files for new additions or information.
- 9) Select
to continue the installation procedures. - 10) The list of Currently Installed Products is again displayed. Verify that EMULEX WAN for NetWare has been added to the list.
- 11) Highlight EMULEX WAN for NetWare and press
to access the Internetworking Configuration menu. - 12) You are now ready to configure the Emulex DCP_link adapter and create specific WAN links. Please turn to Chapter 5, Software Configuration to continue.
- 2) Select Product Options and press
- 1) At the NetWare server system console prompt, type
- Installing to Novell NetWare version 4.1
- 1) At the NetWare server system console prompt, type
- 2) Select Product Options, then press
. - 3) Install on Local Server Only is highlighted; press
. - 4) When the source files have been copied, the following message is displayed:
- 5) Press
, the Installation Options menu will again be displayed. - 6) Select Display Log File to check for any installation problems. A list of any files that were not installed (for any reason) is displayed at the bottom of the file.
- 7) Select Display README Files for new additions or information.
- 8) Select
to continue the installation. The list of Currently Installed Products is displayed. Verify that EMULEX WAN for NetWare has been added to the list. - 9) Highlight EMULEX WAN for NetWare and press
to access the Internetworking Configuration menu. - 10) You are now ready to configure the Emulex DCP_link adapter and create specific WAN links. Please turn to Chapter 5, Software Configuration to continue.
- 2) Select Product Options, then press
- 1) At the NetWare server system console prompt, type
- Installing to Novell NetWare version 3.12
- Uninstall Procedures
- Uninstall Using NetWare Version 3.12
- 1) At the console server prompt, type:
- 2) Select Network Interfaces. Using the
key, deconfigure all interfaces associated with the Emulex adapter. - 3) Press
to return to previous menu. - 4) Select Boards and remove all Emulex WAN configurations by highlighting all references to the EMXMLID driver and pressing the
key. - 5) At the console server prompt, type:
- 6) Select Product Options and delete the Emulex product
- 7) Exit Installation Options and purge the product files from the hard disk.
- 8) Remove the following directories and all associated files:
- 9) Remove all associated files in:
- 10) Bring down and exit the server.
- 2) Select Network Interfaces. Using the
- 1) At the console server prompt, type:
- Uninstall using NetWare version 4.1
- 1) At the console server prompt, type:
- 2) Select Network Interfaces. Using the
key, deconfigure all interfaces associated with the Emulex adapter. - 3) Press
to return to the Internetworking Configuration menu. - 4) Select Boards and remove all configurations by highlighting all references to the EMXMLID driver and pressing the
key. - 5) At the console server prompt, type:
- 6) Select Driver Options from the Installation Options menu, select Configure the Network Drivers and press
. - 7) Using arrow keys, highlight Deselect a Selected Driver and press
. - 8) Use the arrow keys to select the EMXMLID driver and press
or to remove it. - 9) Return to the Installation Options menu and select Product Options.
- 10) From the Other Installation Actions menu, select View/Configure/Remove Installed Products.
- 11) Using the arrow keys, highlight the Emulex product and press the
key to remove the product from the installation database. - 12) Exit the Install utility.
- 13) Remove the following directories and all associated files:
- 14) Remove all associated files in:
- 15) Bring down and exit the server.
- 2) Select Network Interfaces. Using the
- 1) At the console server prompt, type:
- Uninstall Using NetWare Version 3.12
- What’s Next?
- Software Installation Procedure
- Chapter 4
- WANINST5.DOC
- WANINST6.DOC
- Chapter 6
- Introduction
- Configuring the Network Interface
- 1) At the server prompt, type
- 2) Select Network Interfaces, then press
- 3) The network interfaces for the Emulex DCPx86i/e adapter will be displayed. Each interface is associated with a physical port. Select the port (interface) for configuration and press
. - 4) Select Frame Relay (EMX F Relay) from the Available Media, then press
. The DCP_link Frame Relay Network lnterface Configuration menu is displayed. - 5) Press
to display a list of the Emulex DCPx86i/e adapters that are installed. - 6) Select the adapter you wish to configure and press
. - 7) Press
to display the Interface Options menu. The PAL# will be displayed. If a different PAL# is to be used, install the corresponding files first and then select the correct PAL# from the list. - 8) Press
to choose the Data Encoding option, NRZ or NRZI. - 9) In the Interface Speed field, press
to display a list of line clocking rates. Choose External for modem operation. Generally, the service provider will be DCE and the default “External” will be used. - 10) Interface Status: Press
to select the Interface Status (normally Enabled). - 11) DLCI Values: Displays the configured DLCI (Data Link Connection Identifier). Press to add a new DLCI number as assigned by the Frame Relay provider.
- 12) Check the Parameter Group to ensure all selections match the requirements of your service provider.
- Configuring WAN Call Directory
- 1) If you are not already in the Internetworking Configuration menu, load INETCFG from the server prompt:
- 2) Select WAN Call Directory, then press
- 3) Press to configure a new WAN Call Destination.
- 4) Enter a name for the new WAN Call Destination, then press
. - 5) Select EMX F Relay as the wide area medium. The Frame Relay Call Destination Configuration menu is displayed:
- 6) Interface Name: Press
to select the Network interface that has been defined for EMX F Relay. - 7) Circuit Type: Permanent, the default, is the only option available.
- 8) DLCI Number: Press
to select the local DLCI (circuit number) entered in the Network Interfaces screen. - 9) After defining all the necessary parameters, press
and select Yes to save the changes to the Frame Relay WAN Call Destination Configuration.
- Network Protocols and Bindings
- What’s Next?
- Chapter 6
- WANINST7.DOC
- Chapter 7
- Introduction
- Configuring the X.25 Network Interface
- 1) At the server prompt, type
- 2) Select Network Interfaces and press
. - 3) Select an unconfigured interface (port) associated with the Emulex WAN adapter.
- 4) Choose EMX X.25 from the available media and press
. - 5) Card Type: Select the Emulex adapter type if not already displayed.
- 6) Interface Options: Press
to select Interface Options. - 7) Interface Speed: Press
and select the line clocking rate (default is “External” for modem operation). - 8) Interface Status: Displays the current status of the selected network interface (normally enabled).
- 9) Interface Group: Assigns this interface as a member of a collective group of WAN interfaces. WAN Call Destinations can then be assigned to the same collective interface groups. This enables protocols like IPX or IP to request an X.25 virtual circuit through any available interface within the group. The WAN interface actually used for the call is dynamically determined at the time the call is made.
- 10) Press
to select an Interface Group. Select a group from the list or press to create a new Interface group. - Modifying/Creating a Profile
- Local DTE Address
- 1) Enter the access address provided by your local X.25 network service provider.
- 2) Statistics Period - Specifies the interval (seconds) that the network interface (port) is interrogated by the driver for statistical information.
- 3) Interface Queue Limit - Specifies the maximum number of data packets that can be queued to this port. The range of values is 0 (unlimited) through 1024 packets. The default value is 100 packets. Selecting 0 disables the queue limit, allowing unlimited queue depth.
- 1) Enter the access address provided by your local X.25 network service provider.
- X.25 Authentication Options
- Configuring the WAN Call Directory
- 1) From the Internetworking Configuration menu, select WAN Call Directory, and press
- 2) The Configured Wan Call Destinations window is displayed:
- Expert Call Configuration
- 1) If Circuit Type is Switched Virtual Circuit, press
to view or modify the Expert Call Configuration parameters. - 2) In the Request Reverse Charging field, accept the default value No, or press
to change it. - 3) In the Fast Select field, accept the default value, No, or press
to change it. - 4) If Fast Select has been enabled, the With Restriction field can be selected. Accept the default value, No, or, press
to change it. - 5) In the Call User Data field, accept the default value, None, or press
to change it. - 6) In the Generic CCITT Facilities Entry field, accept the default value, or press
to change it. - 7) In the Generic National Facilities field, accept the default value, or press
to change it. - 8) In the Suppress Calling DTE Address field, accept the default value, or press
to change it. - 9) When you have completed all changes to the X.25 Expert Call Configuration parameters, press
to return to the X.25 Call Destination Configuration window. - 10) In the Inbound Authentication Update field, accept the default value, Enabled, or press
to select Disabled. - 11) Press
; if prompted, select Yes to save your changes, then press .
- 2) In the Request Reverse Charging field, accept the default value No, or press
- 1) If Circuit Type is Switched Virtual Circuit, press
- 1) From the Internetworking Configuration menu, select WAN Call Directory, and press
- Network Protocol and Binding
- Chapter 7
- WANINST8.DOC
- WANAPPA.DOC