beautypg.com

Password not displayed in any form, Logging, Fips compliance – H3C Technologies H3C S12500-X Series Switches User Manual

Page 160: Password control configuration task list

background image

148

[SwitchA-Vlan-interface1] ip address 2.2.2.1 255.255.255.0

[SwitchA-Vlan-interface1] quit

# Define an ACL to identify data flows from Switch A to Switch B.

[SwitchA] acl number 3101

[SwitchA-acl-adv-3101] rule 0 permit ip source 2.2.2.1 0 destination 2.2.3.1 0

[SwitchA-acl-adv-3101] quit

# Create an IPsec transform set named tran1.

[SwitchA] ipsec transform-set tran1

# Specify the encapsulation mode as tunnel.

[SwitchA-ipsec-transform-set-tran1] encapsulation-mode tunnel

# Specify the security protocol as ESP.

[SwitchA-ipsec-transform-set-tran1] protocol esp

# Specify the ESP encryption and authentication algorithms.

[SwitchA-ipsec-transform-set-tran1] esp encryption-algorithm aes-cbc-192

[SwitchA-ipsec-transform-set-tran1] esp authentication-algorithm sha1

[SwitchA-ipsec-transform-set-tran1] quit

# Create the IKE keychain named keychain1.

[SwitchA] ike keychain keychain1

# Configure the pre-shared key used with the peer 2.2.3.1 as plaintext string of

12345zxcvb!@#$%ZXCVB.

[SwitchA-ike-keychain-keychain1] pre-share-key address 2.2.3.1 255.255.255.0 key

simple 12345zxcvb!@#$%ZXCVB

[SwitchA-ike-keychain-keychain1] quit

# Create the IKE profile named profile1.

[SwitchA] ike profile profile1

# Reference the keychain keychain1.

[SwitchA-ike-profile-profile1] keychain keychain1

[SwitchA-ike-profile-profile1] match remote identity address 2.2.3.1 255.255.255.0

[SwitchA-ike-profile-profile1] quit

# Create an IKE-based IPsec policy entry, with the policy name map1 and sequence number 10.

[SwitchA] ipsec policy map1 10 isakmp

# Apply ACL 3101.

[SwitchA-ipsec-policy-isakmp-map1-10] security acl 3101

# Apply the IPsec transform set tran1.

[SwitchA-ipsec-policy-isakmp-map1-10] transform-set tran1

# Specify the local and remote IP addresses of the IPsec tunnel as 2.2.2.1 and 2.2.3.1.

[SwitchA-ipsec-policy-manual-map1-10] local-address 2.2.2.1

[SwitchA-ipsec-policy-manual-map1-10] remote-address 2.2.3.1

# Apply the IKE profile profile1.

[SwitchA-ipsec-policy-isakmp-map1-10] ike-profile profile1

[SwitchA-ipsec-policy-isakmp-map1-10] quit

# Specify the card in slot 1 to process the traffic for VLAN-interface 1.

[SwitchA] interface vlan-interface 1

[SwitchA-Vlan-interface1] service slot 1

# Apply the IPsec policy map1 to VLAN-interface 1.

This manual is related to the following products:
See also other documents in the category H3C Technologies Routers: