REMKO Multi-talent - Manual (Page 56)

REMKO HEAT PUMP MANAGER
Designation Value range Programming
Output/level 00 – 9950 kW
WE 1 level 1 = 50
WE 3 level 1 = 1
continue with key next to "End"
MF 1 function
0 0 - 3 6 0 0
T - MF 1 target - 2 0 °C - 9 0 °C ( ---- )
MF 1 Hyst 2 K - 1 0 K ( ---- )
MF 1 Hyst Off 2 K - 1 0 K ( ---- )
MF 2 function 0 0 - 3 6 18
T - MF 2 target - 2 0 °C - 9 0 °C ( ---- )
MF 2 Hyst 2 K - 1 0 K ( ---- )
MF 2 Hyst Off 2 K - 1 0 K ( ---- )
MF 3 function 0 0 - 3 6 3 4
T - MF 3 target - 2 0 °C - 9 0 °C ( ---- )
MF 3 Hyst 2 K - 1 0 K ( ---- )
MF 3 Hyst Off 2 K - 1 0 K ( ---- )
MF 4 function 0 0 - 3 6 2 3
T - MF 4 target - 2 0 °C - 9 0 °C ( ---- )
MF 4 Hyst 2 K - 1 0 K 5,0K
MF 4 Hyst Off 2 K - 1 0 K 2,0K
F15 function 0 0 - 0 8 0 7
E 1 function 0 0 - 0 3 0 2
E 2 function 0 0 - 0 3 0 3
Sensor 1k/5k sensors 5k sensors
Designation Value range Programming
BUS code BM Off, 00-15 Off
Language D/GB/F/NL/E/I D (German)
Terminal address On / Off On
Time 0-24 Set time
Date Year, month, day Set date
BUS code 1 00-15 01
BUS code 2 00-15 02
System selection ---/01-12 07
Regulator type 00-06 06
WE 1 type 00-09 07
WE BUS 00-05 05
Gradient On / Off Off
WE 2 type 00-22 08
WE 2 tank 00-03 00
WE 3 type 00-09 01
WE 4 type 00-09 00
Buffer type 00-02 00
Cooling mode Off/On On
HC1 function
Standard,T-feed
const, swimming
pool, WW,
return
Standard
HC2 function see HC1 Standard
B
A
AB
F9 F14
A
B
AB
F6
F8
F12
A
B
AB
l/h
Tmax
V V
F17 F11
II 0 I
3)
A9
A3
A6
A12
A3
A10
A8
M
2)
1)
F5
A2
A4/A5
A10
4)
Hydraulic diagram for the heat pump assembly 11
Functions: Heating or cooling, hot water and solar
monoenergetic operating mode
“System selection 7”
Multi-function
Storage tank
MPS 1000
Outdoor unit
Indoor unit
CMF 120/160
EMF/EMT 100/150
Heating circuit
Taps
CW inlet
Fresh water station
Cooling circuit
Cooling water
Storage tank
KPS 300
Notes:
1) Heating circuit circulation pump(s) not included in REMKO's scope of delivery. We recommend the use of high-efficiency circulation pumps.
2) We recommend, because of possible high temperatures - caused by the solar plant, to always connect the heating circuit via a 3-way mixer.
3) If a circulation pump is installed, it must be controlled separately.
4) The cooling must be activated via heating circuit 1 by setting T-supply cooling to the desired cooling target supply temperature.
Sample hydraulic diagram for system selection 7
56