Orion System VCC-X Controller - Manual (Page 11)

OVERVIEW
11 VCC-X Controller Technical Guide
PART NO. PART DESCRIPTION ILLUSTRATION PAGE NO.
OE392-12 Modular System Manager SD
Includes: Modular System Manager SD with 4 Gigabyte SD card and 12 ft.
long pigtail cable assembly. Used to program and monitor all Orion
controllers. Designed for hollow core wall mounting. When System
Manager is to be mounted on a solid wall (concrete), you will also need
to order the solid wall mounting bracket below. Modular System Manager,
power supply, communication cables,
See VCC-X
Controller
Operator
Interfaces
SD
Technical
Guide
EB101505 Solid Wall Mounting Bracket for Modular System Manager
SD
Includes: 22 gauge galvanized sheet metal mounting bracket with mount-
ing holes and wire routing opening. Dimensions are 9.25″W x 8.00″H x
0.50″DP. The Wall Mounting Bracket provides wiring clearance between
the System Manager and the wall mounting surface when the System
Manager is to be mounted on a concrete or other solid wall surface. Not
for use with System Manager TS.
OE361-13 CommLink 5 Communications Interface
The CommLink 5 connects to your control system using a USB computer
connection to provide direct on-site communications with the control
system from a computer with the Prism 2 software installed. For remote
communications, see OE415-02 IP Module Kit.
Includes: CommLink 5, 6 ft. long USB cable, and 120/24 VAC power sup-
ply. Required on all networked systems or if direct computer or remote
computer connection is required. Connects to your computer’s USB 1.1
or 2.1 port. Prism 2 computer front-end software must be installed on the
direct connected or remote connected computer in order to communicate
with your system.
STATUS
See
CommLink
5 Technical
Guide
OE415-02 IP Module Kit - Internet/LAN Connection
Used for Internet or Local Area Network communications with the control
system. Field installs by plugging into the CommLink 5 circuit board and
provides an addressable Ethernet connection to the controls system from
any computer connected to your building’s LAN. It can also be confi gured
to allow access to the control system from the Internet through your LAN if
your Ethernet fi rewall is confi gured for this option.
Includes: IP Link module, 10 ft. long Ethernet cable, and installation
instructions. Prism 2 computer front-end software must be installed on the
remote computer in order to dial-up and communicate with the controls
system.
See IP
Module
Technical
Guide
OE366 USB-Link 2 Kit
The USB-Link 2 is a pocket-sized communications interface used to
connect a laptop computer to your controls system for programming and
monitoring purposes, utilizing a modular cable to allow connection to the
service port connector on the controllers and a USB cable to connect to a
laptop computer.
Includes: USB-Link 2 for multiple or single loop systems, USB cable,
modular connection cable, two mini-DIN to terminal adapters, and Prism 2
software.
See USB-
Link 2
Technical
Guide
OE364-22 MiniLink Polling Device
Control enclosure is for indoor use only. Used with all Orion controllers
to provide network communications, zone voting, alarming, and tenant
logging capabilities. A MiniLink Polling Device is required on each loop
of a Networked system. Includes: MiniLink Polling Device mounted in
the EE000075-01 control enclosure. Control Enclosure cover is shown
removed in picture.
EPROM
U3
U5
RAM CX2
1 U2 R1 C3
U4 CX3 CX4 YS 101818 P552 PROC ESSO RPBO AR D CX5 C1
U1
R2
CX1 CX6
WDOG
U6
PHIL IP S D1
P1 X1 C2
C4
0-10V 4-20mA THERM R27
R3 1 D4 GN D 24 V A C
TB 1 D5 C11
U12
LED 2
POWER
V1 R2 5 R2 6 C7
CX 15 CX13 PROC. DRIVER LOOP DRIVER
LOCAL LOOP GND AIN 2 AIN 1 +5 V
TB2 P4 OFF=0-5V
AIN2 AIN1
0-10V 4-20mA THERM
SH LD T TB 3 R
U1 5 LD5 LD6 U1 3
C8
LED 1
RV1
R4
VREF CX 2
U11
YS101900PMINILINK POLLING DEVICE REV. 1
OFF
1 2 4 8 16 32
CX 14 NETWORK DRIVER RN3
SH LD T TB4 R
U1 4 NETWORK LOOP P5 ADD
P3
R24
LD4 C9
U10
RN2
SW1
R30
X2 R29 R28
C10
U6
CX 6
CX1 U7 U1
X1 C3
C1 R3
CX7
Parts and Descriptions