Comtech EF Data SNM-1002 User Manual
Page 145
SNM-1002 LinkSync
Modem
Revision 2
Remote Control Operation
MN/SNM1002.OM
A–19
MTIT_7_yyyyy'cr' (Note 7)
MTCP_7_yyy'cr' (Note
7)
MTDP_7_yyy'cr' (Note
7)
MTMD_7_yyyyy'cr' (Note
7)
MTAF_7_yyy'cr' (Note
7)
MTDR_8_yyyyyy'cr' (Note
7)
MTIT_8_yyyyy'cr' (Note 7)
MTCP_8_yyy'cr' (Note
7)
MTDP_8_yyy'cr' (Note
7)
MTMD_8_yyyyy'cr' (Note
7)
MTAF_8_yyy'cr' (Note
7)
TCEN_1_xxxx'cr' (Note 8)
TCDR_1_xxxx.x'cr' (Note 9)
TCEN_2_xxx'cr'
(Note 8)
TCEN_3_xxxx'cr' (Note 8)
TCDR_3_xxxx.x'cr' (Note 10)
TCCP_3_yyy'cr' (Note
10)
TCDP_3_yyy'cr' (Note
10)
TCEN_4_xxxx'cr' (Note 8)
TCDR_4_xxxx.x'cr' (Note 11)
TCCP_4_yyy'cr' (Note
11)
TCDP_4_yyy'cr' (Note
11)
RCEN_1_xxxx'cr' (Note 8)
RCDR_1_xxxx.x'cr' (Note 12)
RCEN_2_xxx'cr'
(Note 8)
RCEN_3_xxxx'cr' (Note 8)
RCDR_3_xxxx.x'cr' (Note 13)
RCCP_3_yyy'cr' (Note
13)
RCDP_3_yyy'cr' (Note
13)
RCEN_4_xxxx'cr' (Note 8)
RCDR_4_xxxx.x'cr' (Note 14)
RCCP_4_yyy'cr' (Note
14)
RCDP_4_yyy'cr' (Note
14)
'lf']
Mux Tributary #7 Interface Type
Mux Tributary #7 Clock Phase
Mux Tributary #7 Data Phase
Mux Tributary #7 Mode
Mux Tributary #7 Async Mode
Mux Tributary #8 Data Rate & Enable
Mux Tributary #8 Interface Type
Mux Tributary #8 Clock Phase
Mux Tributary #8 Data Phase
Mux Tributary #8 Mode
Mux Tributary #8 Async Mode
Flex Mux TX Channel #1 Enable
Flex Mux TX Channel #1 Data Rate
Flex Mux TX Channel #2 Enable
Flex Mux TX Channel #3 Enable
Flex Mux TX Channel #3 Data Rate
Flex Mux TX Channel #3 Clock Phase
Flex Mux TX Channel #3 Data Phase
Flex Mux TX Channel #4 Enable
Flex Mux TX Channel #4 Data Rate
Flex Mux TX Channel #4 Clock Phase
Flex Mux TX Channel #4 Data Phase
Flex Mux RX Channel #1 Enable
Flex Mux RX Channel #1 Data Rate
Flex Mux RX Channel #2 Enable
Flex Mux RX Channel #3 Enable
Flex Mux RX Channel #3 Data Rate
Flex Mux RX Channel #3 Clock Phase
Flex Mux RX Channel #3 Data Phase
Flex Mux RX Channel #4 Enable
Flex Mux RX Channel #4 Data Rate
Flex Mux RX Channel #4 Clock Phase
Flex Mux RX Channel #4 Data Phase
The Interface configuration status command
causes a block of data to be returned by the
addressed MODEM. The block reflects the
current configuration of the interface.
Additional configuration status of new options
and features will always be appended to the
end.
Notes:
1. Data is only returned for TX D&I Overhead.
2. Data is only returned for RX D&I Overhead.
3. Data is only returned for TX IDR Overhead.
4. Data is only returned for RX IDR Overhead.
5. Data is only returned for TX ASYNC
Overhead.
6. Data is only returned for RX ASYNC
Overhead.
Data is only returned if MUX PCB (Card Slot
#1) is installed.
8.
Data is only returned if FLEX MUX PCB (Card Slot
#1) is installed.
9.
Data not returned if TX Channel #1 is disabled.
10. Data not returned if TX Channel #3 is disabled or
set for AUPC.
11. Data not returned if TX Channel #4 is disabled or
set for AUPC.
12. Data not returned if RX Channel #1 is disabled.