Comtech EF Data SNM-1002 - Manual (Page 138)

SNM-1002 LinkSync
 Modem
Revision 2
Remote Control Operation MN/SNM1002.OM
A–12
A.4 Status Commands/Responses
Modulator
Config.
Status
Command:
Response:
>add/MCS_'cr'
RF_xxx'cr'
MF_nnn.nnnnnn'cr'
MR_nnnn_mmmm.mmm'cr'
AMRA_nnnn_mmmm.mmm'cr'
AMRB_nnnn_mmmm.mmm'cr'
AMRC_nnnn_mmmm.mmm'cr'
AMRD_nnnn_mmmm.mmm'cr'
AMRV_nnnn_mmmm.mmm'cr'
MPO_snn.n'cr'
MOP_snn.n'cr'
SE_xxx'cr'
DENC_xxx'cr'
MT_xxxxx'cr'
MET_xxx'cr'
COM_xxxxxx'cr'
MRC_xxx'cr'
MSR_xxx'cr'
RSEN_xxx'cr'
TDA_xxx'cr'
TRSI_xx'cr'
T310_xxx'cr''lf']
RF Output
Modulator Frequency
Modulator Rate
Preset 'A' Assignment
Preset 'B' Assignment
Preset 'C' Assignment
Preset 'D' Assignment
Preset 'V' Assignment
Modulator Power Offset
Modulator Output Power
Scrambler Enable
Differential Encoder
Modulator Type
Modulator Encoder Type
Carrier Only Mode
Modulator Reference Clock
Modulator Spectrum Rotation
Reed-Solomon Encoder
Transmit BPSK Data Ordering
TX Reed-Solomon Interleave Value
TX 8PSK 2/3 IESS-310 Operation
The modulator configuration status command
causes a block of data to be returned by the
addressed modem. The block of data reflects the
current configuration status of the modulator
module. Additional configuration status of new
options and features will always be appended to
the end.
Modulator/
Coder
Config.
Program
Status Command:
Response:
>add/MCP_'cr'
SMT_xxxxxxx'cr'
ITOT_xxxxx'cr'
MOM_xxxxxxx'cr'
MT_xxxxx'cr'
MET_xxx'cr'
TCEN_1_xxxx'cr' (Note 1)
TCDR_1_xxxx.x'cr' (Note 2)
TCEN_2_xxx'cr'
(Note 1)
TCEN_3_xxxx'cr' (Note 1)
TCDR_3_xxxx.x'cr' (Note 3)
TCCP_3_yyy'cr' (Note
3)
TCDP_3_yyy'cr' (Note 3)
TCEN_4_xxxx'cr' (Note 1)
TCDR_4_xxxx.x'cr' (Note 4)
TCCP_4_yyy'cr' (Note
4)
TCDP_4_yyy'cr' (Note 4)
MF_nnn.nnnnnn'cr'
MR_nnnn_mmmm.mmm'cr'
MPO_snn.n'cr'
LPC_xxx'cr' (Note
5)
MOP_snn.n'cr' (Note 6)
SE_xxx'cr'
System Modem Type
Interface Transmit Overhead Type
Modem Operation Mode
Modulator Type
Modulator Encoder Type
Flex Mux TX Channel #1 Enable
Flex Mux TX Channel #1 Data Rate
Flex Mux TX Channel #2 Enable
Flex Mux TX Channel #3 Enable
Flex Mux TX Channel #3 Data Rate
Flex Mux TX Channel #3 Clock Phase
Flex Mux TX Channel #3 Data Phase
Flex Mux TX Channel #4 Enable
Flex Mux TX Channel #4 Data Rate
Flex Mux TX Channel #4 Clock Phase
Flex Mux TX Channel #4 Data Phase
Modulator Frequency
Modulator Rate
Modulator Power Offset
AUPC Local Power Enable
Modulator Output Power